American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Keepsake Box East Greenwich RI

The box shown at left is made from 3/8-in.-thick wood, so I used a bandsaw for resawing and a planer to take the wood to final thickness. For more information about resawing, check out “Bandsaw Resawing”.

Woodcraft - Providence, RI
(401) 886-1175
1000 Division Street
East Greenwich, RI

Data Provided by:
The Home Depot
(401)823-5173
700 Centre Of N E Blvd
Coventry, RI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(401)845-5092
878 W Main Road
Middletown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(401) 267-6330
1530 Davisville Road
North Kingstown, RI
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Rhode Island Mall
(401) 827-4800
650 Bald Hill Rd
Warwick, RI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5

The Home Depot
(401)295-1184
1255 Ten Rod Road
North Kingstown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Liberty Cedar, Inc.
(401) 789-6626
325 Liberty Lane
West Kingston, RI

Data Provided by:
St. Angelo Hardwoods, Inc. - Genuine Asian Teak Specialist
(401) 624-3900
490 Eagleville Road
Tiverton, RI

Data Provided by:
Wickford Lumber Co True Value
(401) 295-8866
434 Tower Hill Road
North Kingstown, RI
 
S&t True Value Hardware
(401) 397-6300
2300 Nooseneck Hill Rd
Coventry, RI
 
Data Provided by:

Keepsake Box

Keepsake Box

Build them in bunches and avoid gift shopping this year. 

by Mac Wentz

As the holidays approach, my thoughts turn to how I can weasel out of gift shopping. And this year I have the perfect scheme: While the malls are jammed with poor saps, I’ll be in my shop blissfully building these boxes for everyone on my list.

When they marvel at the elegant keyed joinery at the corners, I won’t mention how fast and easy these boxes are to make. Making the jigs and resawing lumber takes a few hours, but once you’re set up you can churn out three or four boxes in a day. There’s no need to mention how cheap the materials are either. If you stick with common species like oak, cherry or maple, each box will cost only $10 to $15.

Tools and Materials

The box shown at left is made from 3/8-in.-thick wood, so I used a bandsaw for resawing and a planer to take the wood to final thickness. For more information about resawing, check out “Bandsaw Resawing”. 

If you don’t have a bandsaw and planer you can also mail order 3/8-in. wood (see Sources, below). You’ll also need a tablesaw, belt sander, router table, 1/8-in. and 3/4-in. straight router bits and some 3-in. spring clamps.

Start With Grain Selection

Grain pattern has a big influence on the appearance of a small project like this box, so don’t just rip up boards and leave it to chance. Begin by making paper windows that let you preview the look of the box parts (Photo 1). I generally use finer, straighter-grained material for the ends and sides and a more dramatic pattern for the top. This is not a hard and fast rule, so experiment until you get something you like. Grain pattern for the bottom isn’t critical, since it doesn’t show. For the keys I use a different color wood so they contrast with the box. 

Cut the Sides

I strongly recommend you miter the box sides on a tablesaw using a tablesaw sled (Photo 2). The every-time accuracy of a well-made tablesaw sled is hard to beat. In fact, I built a small one just for building these boxes. For more information on making a sled, see “The Ultimate Shop-Built Crosscut Sled,” AW #75, October 1999. Cut the parts for the ends and sides and make an extra set to test your machine setups later on. 

Next cut the dadoes in the ends and sides for the bottom (Fig. A, page 55). The dadoes should be wide enough to provide an easy fit for the bottom. 

Now select two ends and two sides that have the least attractive grain and mark them “GP” for guinea pig. These GP parts are the first to go through each step in the machining process and hopefully the only ones to suffer from setup mistakes. Beginning with the GP parts, rout the relief in the bottom of the ends and sides to form the corner feet using a 3/4-in. straight router bit in your router table (Photo 3). 

The Bottom and Top

Cut the bottom for the box next.

Click here to read the rest of the article from American Woodworker