American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Lock Rabbet Drawer Joinery Fort Campbell KY

Setting up the drawer lock bit is not difficult. Start by aligning this bit with the fence, as shown in Photo 1. Next, adjust the height of the bit to approximately 3/8 in. (Photo 2). Run a couple of test boards (Photo 3) and check the fit (Photo 4). The first test boards you make are unlikely to give you a perfect fit, so adjust the bit's height until the fit is just right.

The Home Depot
(931)906-2655
2630 Wilma Rudolph Blvd
Clarksville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Hardware City
(931) 551-3424
1060 S Riverside Dr
Clarksville, TN
 
Lowe's
(931) 920-4102
2150 Lowe'S Drive
Clarksville, TN
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Governor Sq Mall
(931) 553-2100
2801 Wilma Rudolph Blvd
Clarksville, TN
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Kmart 4739 / Cross Merch
(931) 647-2444
2780 Guthrie Hwy
Clarksville, TN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Grandpa's
(931) 647-0251
1894 Fort Campbell Blvd
Clarksville, TN
 
Fastenal- Clarksville
931-906-1878
190 West Dunbar Cave Rd Clarksville, TN, 37040
Clarksville, TN
 
Thomas Lumber Company
(931) 645-2448
2128 Old Ashland City Rd
Clarksville, TN
 
LOWE'S OF CLARKSVILLE, TENN.
931 920-4102
2150 LOWES DRIVE CLARKSVILLE, TN, 37040
Clarksville, TN
 
Lowe's
(270) 707-7201
4580 Fort Campbell Boulevard
Hopkinsville, KY
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Lock Rabbet Drawer Joinery

Lock Rabbet Drawer Joinery

Here's a router-made drawer joint that's quick, simple and self-aligning.

by Randy Johnson

For fast, easy, accurate joinery in everything from kitchen-cabinet drawers to jewelry boxes, the lock rabbet is the way to go. Lock rabbets are self-aligning and sufficiently strong for light- and medium-duty drawers. As with most woodworking techniques, there is more than one way to make a lock rabbet. We experimented with several methods using the tablesaw and router table and settled on this as our favorite. It uses a router bit called a drawer lock bit. And for the wood, we chose 1/2-in. Baltic birch plywood. Its multiple layers and lack of internal voids make it strong and stable.

Router Bit Setup

Setting up the drawer lock bit is not difficult. Start by aligning this bit with the fence, as shown in Photo 1. Next, adjust the height of the bit to approximately 3/8 in. (Photo 2). Run a couple of test boards (Photo 3) and check the fit (Photo 4). The first test boards you make are unlikely to give you a perfect fit, so adjust the bit's height until the fit is just right.

Marking the Drawer Sides

To determine the length of your drawer sides, subtract two times the thickness of the lip on your test board (Photo 4) from your final drawer box length. For example, if you're making a 12-in.-long drawer box and the lip on the test board is 1/16 in., the material for the drawer sides should be 11-7/8-in. long. Here's the math: 

1/16" x 2 = 1/8" 
12" - 1/8" = 11-7/8"

Prepare your plywood by cutting it into panels that equal the length you calculated with the formula above and are two to three drawer-sides wide (Photo 9). Add 1 in. to the width to allow for saw kerfs and edge waste. The edge waste will accommodate the chip-out that usually occurs when the router bit exits the cut. To rout the joint for drawer sides, hold the panel vertically against the fence (Photo 6).

Making the Drawer Box Fronts and Backs

Reset your router-table fence before you rout the fronts and backs. Set a scrap piece of your drawer-box material on top of the bit and move the fence back until the cutting depth matches the thickness of the material (Photo 7). Run a test cut with a scrap of drawer-box material and check the fit with the drawer side panels you cut earlier. It should look like the joint in (Photo 5). If the lip doesn't flush up with the side panel, readjust the router-table fence and run another test cut until the lip is flush with the side.

The drawer fronts and backs should be as long as the final width of the drawer box because they span the full width (Photo 5). These front and back panels are routed flat on the table (Photo 8)

Final Sizing

Now you can saw the drawer parts to final width (Photo 9). Then, saw or rout a 3/16-in.-deep dado in the parts for the drawer bottoms.

Click here to read the rest of the article from American Woodworker