American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Making Cathedral Doors Forest Lake MN

There are a few specialized tools you must have to make cathedral doors. Start with a suitable router table. It should be equipped with a 2-hp or higher variable-speed router that accepts 1/2-in.-shank router bits. You’ll also need a bandsaw or jigsaw for cutting the curves and a set of door-making router bits.

The Home Depot
(651)464-5277
1943 W Broadway Avenue
Forest Lake, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)795-2060
99 Northtown Drive
Blaine, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)571-9600
5650 Main St, NE
Fridley, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #13
(651) 773-5285
1935 Beam Avenue
Maplewood, MN

Data Provided by:
Forest Lake Ace Hardware
(651) 464-6262
814 Lake St S, Lake Shoppes Mall
Forest Lake, MN
 
The Home Depot
(763)717-0316
4550 Pheasant Ridge Dr
Blaine, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)422-1200
3550 124th Ave NW
Coon Rapids, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(651)770-9600
2360 White Bear Ave No
Maplewood, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Forest Lake - Auth Hometown
(651) 982-9997
24135 Greenway Rd
Forest Lake, MN
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:10-16
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:10-16

Fastenal- Forest Lake
651-464-4320
24078 Greenway Rd Unit #7 Forest Lake, MN, 55025
Forest Lake, MN
 
Data Provided by:

Making Cathedral Doors

Making Cathedral Doors

A complete recipe for making beautiful cathedral raised-panel doors.

by George Vondriska

Cathedral raised-panel doors are beautiful, but they can be intimidating to make. After many years of teaching students how to make these doors, I’ve got a trick or two up my sleeve to simplify the process and remove some of the fear factor. Here’s a tried-and-true recipe to help you safely and successfully make beautiful doors.

There are a few specialized tools you must have to make cathedral doors. Start with a suitable router table. It should be equipped with a 2-hp or higher variable-speed router that accepts 1/2-in.-shank router bits. You’ll also need a bandsaw or jigsaw for cutting the curves and a set of door-making router bits. The bits and a template set will set you back nearly $400, but they are a big part of what makes this technique airtight. The good news is the router bits are not specific to cathedral-top doors; they can be used to make any frame-and-panel door.

You’ll need a two-piece matched rail-and-stile set (about $135) to make the frame. It’s easier to get good results with a two-piece set than with a one-piece reversible bit. With a two-piece set, you feed all the pieces face down. Reversible bits use one arbor with removable cutters. Some parts are machined face up, others face down. This often results in poor alignment between rails and stiles. Plus, it’s a hassle to have to change cutters on the arbor. Bits with a 1/2-in. shank will produce less chatter and a smoother cut than those with 1/4-in. shank. 


First, cut all the frame pieces (see “Sizing a Door, below”). For a good-looking, stable door, make the frame from straight-grained wood. 

Next, on your router table, set up the end-grain cutter for machining the rail ends. Cutting end grain before long grain helps prevent blow-out on the rails. Here’s a memory device for you: Machine the Rails before the Stiles, because R comes before S in the alphabet.

Mark the back of all the frame pieces. They get machined with their good faces down, so you should be looking at the mark on the back for all the cuts.

Note: Run the end-grain and long-grain cutters at full speed on your router.

Photo 1: Set the height of the end-grain cutter against a test piece in the coping sled. The cut should leave a shoulder on top of the piece that’s twice as thick as the lip on the bottom (see Photo 4). You can tweak the height after a test cut. 

Photo 2: Set the fence even with the face of the ball bearing. A straightedge makes quick work of this job.

Photo 3: Make a test cut, but don’t cut all the way through the test piece. You don’t want to cut into the backer block until the bit height is perfect. That way, the block can be used to quickly set the bit height the next time you make doors.

Click here to read the rest of the article from American Woodworker