American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Making Cathedral Doors Greeneville TN

There are a few specialized tools you must have to make cathedral doors. Start with a suitable router table. It should be equipped with a 2-hp or higher variable-speed router that accepts 1/2-in.-shank router bits. You’ll also need a bandsaw or jigsaw for cutting the curves and a set of door-making router bits.

Full Cycle Woodworks Inc.
(423) 272-9004
1600 Hwy 70 North
Rogersville, TN

Data Provided by:
Fastenal- Greeneville
423-638-3622
730 W. Andrew Johnson Hwy Greeneville, TN, 37743
Greeneville, TN
 
Kmart 3773 / Cross Merch
(423) 636-1118
1355 Tusculum Blvd
Greeneville, TN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Lowe's
(423) 788-7000
1498 E. Jackson Boulevard
Jonesborough, TN
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Appalachian Stoneworks
(866) 389-4260
412 Kinchloe Mill Rd
Jonesborough, TN

Data Provided by:
Ace Hardware
(423) 639-6223
1023 W Main St
Greeneville, TN
 
LOWE'S OF GREENEVILLE, TENN.
423 639-0012
2375 EAST ANDREW JOHNSON HIGHWAY GREENEVILLE, TN, 37745
Greeneville, TN
 
Lowe's
(423) 639-0012
2375 East Andrew Johnson Highway
Greeneville, TN
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Olde Towne Ace Hardware
(423) 913-1606
220 N 2nd Ave
Jonesborough, TN
 
Woodcraft - Nashville, TN
(615) 599-9638
209 S. Royal Oaks Blvd.
Franklin, TN

Data Provided by:
Data Provided by:

Making Cathedral Doors

Making Cathedral Doors

A complete recipe for making beautiful cathedral raised-panel doors.

by George Vondriska

Cathedral raised-panel doors are beautiful, but they can be intimidating to make. After many years of teaching students how to make these doors, I’ve got a trick or two up my sleeve to simplify the process and remove some of the fear factor. Here’s a tried-and-true recipe to help you safely and successfully make beautiful doors.

There are a few specialized tools you must have to make cathedral doors. Start with a suitable router table. It should be equipped with a 2-hp or higher variable-speed router that accepts 1/2-in.-shank router bits. You’ll also need a bandsaw or jigsaw for cutting the curves and a set of door-making router bits. The bits and a template set will set you back nearly $400, but they are a big part of what makes this technique airtight. The good news is the router bits are not specific to cathedral-top doors; they can be used to make any frame-and-panel door.

You’ll need a two-piece matched rail-and-stile set (about $135) to make the frame. It’s easier to get good results with a two-piece set than with a one-piece reversible bit. With a two-piece set, you feed all the pieces face down. Reversible bits use one arbor with removable cutters. Some parts are machined face up, others face down. This often results in poor alignment between rails and stiles. Plus, it’s a hassle to have to change cutters on the arbor. Bits with a 1/2-in. shank will produce less chatter and a smoother cut than those with 1/4-in. shank. 


First, cut all the frame pieces (see “Sizing a Door, below”). For a good-looking, stable door, make the frame from straight-grained wood. 

Next, on your router table, set up the end-grain cutter for machining the rail ends. Cutting end grain before long grain helps prevent blow-out on the rails. Here’s a memory device for you: Machine the Rails before the Stiles, because R comes before S in the alphabet.

Mark the back of all the frame pieces. They get machined with their good faces down, so you should be looking at the mark on the back for all the cuts.

Note: Run the end-grain and long-grain cutters at full speed on your router.

Photo 1: Set the height of the end-grain cutter against a test piece in the coping sled. The cut should leave a shoulder on top of the piece that’s twice as thick as the lip on the bottom (see Photo 4). You can tweak the height after a test cut. 

Photo 2: Set the fence even with the face of the ball bearing. A straightedge makes quick work of this job.

Photo 3: Make a test cut, but don’t cut all the way through the test piece. You don’t want to cut into the backer block until the bit height is perfect. That way, the block can be used to quickly set the bit height the next time you make doors.

Click here to read the rest of the article from American Woodworker