American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Making Curved Doors Hobbs NM

Curved doors and panels add elegance to any project, especially kitchen cabinets. Making these complicated parts requires careful planning and building. The task can be made much easier by using a flexible panel product called Kerfkore (see photo, below left).

The Home Depot
(575)492-9117
900 W Joe Harvey Blvd
Hobbs, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 7016 / Cross Merch
(575) 397-3587
2220 N Grimes St
Hobbs, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Hobbs - Auth Hometown
(575) 492-0445
405 E Navajo Dr
Hobbs, NM
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18.5
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18.5
Sun:12-17

The Home Depot
(505)865-0425
1800 Main Street NW
Los Lunas, NM
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(505)899-1290
10200 Coors Dr NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Fastenal- Hobbs
505-393-8831
321 West Broadway Hobbs, NM, 88240
Hobbs, NM
 
Lowe's
(575) 492-3230
1510 West Joe Harvey Boulevard
Hobbs, NM
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

The Home Depot
(575)443-8018
3400 N White Sand Blvd
Alamogordo, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(505)271-1900
200 Eubank Blvd SE
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(575)492-9117
900 W Joe Harvey Blvd
Hobbs, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Making Curved Doors

Making Curved Doors

Kerfkore flexible panels handle curves with ease.

by Brad Holden

Curved doors and panels add elegance to any project, especially  kitchen cabinets. Making these complicated parts requires careful planning and building. The task can be made much easier by using a flexible panel product called Kerfkore (see photo, below left). It follows the same principle that cabinetmakers use when they saw multiple kerfs on the back of a piece of plywood to make it flexible. A disadvantage to this saw-kerfing method is the risk of the face veneer cracking or kinking at the kerfs, spoiling the curve’s smooth surface. Kerfcore’s advantage is that that the kerfing is done for you. Its flexible paper backing provides a smooth surface to attach your veneer. 

There are several important tricks and techniques to working with Kerfkore but it’s a surprisingly easy material to work with. I’ll walk you through the main steps of making a curved door with Kerfkore from layout to final trimming. Information on using Kerfkore in other applications can be found at the Web site www.kerfkore.com.

What is Kerfkore?

Kerfkore is a very flexible panel made of 3/8-in.-wide ribs spaced 1/8 in. apart on a paper backer sheet. The spaces between the ribs allows the board to flex. The flexible backer sheet provides a smooth surface for veneering. The ribs in different Kerfkore products are made of particleboard, luan plywood, poplar plywood, MDF, fire-rated treated particleboard or lightweight styrene foam. These different cores have different weights, strengths and screw-holding characteristics. The particleboard core works well for general-purpose doors, such as those for kitchen cabinets. 

Kerfkore with paper backer on both sides is also available. This makes the material more rigid and somewhat easier to handle and enables you to create a curve that turns into a straight run. To make the two-sided variety bend, you cut the backer on one side with a utility knife where you need the bend to occur. 

Kerfkore comes in 4-ft. by 8-ft. sheets in 1/4-in., 3/8-in., 1/2-in., 5/8-in. and 3/4-in. thicknesses and costs between $40 and $125 per sheet (see Sources, below). 

Pick Your Veneer

Photo 1: Your three main veneer choices are two-ply wood veneer (shown here), phenolic-backed (plastic-laminate) wood veneer or vertical-grade plastic laminate. The two-ply veneer is the most flexible of the three and is easily cut with a utility knife or scissors. The phenolic-backed veneer and plastic laminate must be sawn or scored and snapped. The cut edge of the two-ply veneer leaves a dark line that may show on your finished door, depending on the wood species and the finish you apply. The phenolic-backed veneer and plastic laminate both leave a black edge line. 

Make a Full-Size Drawing

Photo 2: Use a top-view drawing to determine the size of the Kerfkore panel and the angles at the edges. T...

Click here to read the rest of the article from American Woodworker