American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Master Your Brad Nailer Mandan ND

If your firing angle parallels the growth rings, the brad will simply deflect off the hard latewood. Increase the air pressure when you nail into hard wood. Just like a putt that falls off line when it loses speed, a brad driven softly is more likely to deflect.

Fastenal- Mandan
701-663-4160
601 Burlington St SE Mandan, ND, 58554
Mandan, ND
 
ACME TOOLS- Bismark
(701) 258-1267
3840 East Rosser Ave Bismarck, ND, 58501
Bismarck, ND
 
Gateway Mall
(701) 258-0111
2700 State St
Bismarck, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-19
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-19
Sun:12-18

Fastenal- Bismarck
701-255-4408
1405 Airport Rd Bismarck, ND, 58504
Bismarck, ND
 
The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Bismarck Lumber Co.
(701) 223-2145
2200 E Main
Bismarck, ND
 
Lowe's
(701) 934-9000
1401 Century Avenue West
Bismarck, ND
Hours
M-SA 7 am - 9 pm
SU noon-8 pm

Bismarck - D
(701) 223-0074
2625 State St
Bismarck, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Kirkwood Hardware
(701) 258-6161
805 S 7th St, Target and Barnes & Noble
Bismarck, ND
 
Kindred Implement & True Value Hdw
(701) 428-9119
321 Hwy 46
Kindred, ND
 

Master Your Brad Nailer

Master Your Brad Nailer

Tips and products to make your brad nailer safe and easy to use.

Tim Johnson

Avoid the Blowout Curse

A brad that unexpectedly shoots out the side of your project is guaranteed to make you curse, especially if your finger happens to be in the way. Blowout is instantaneous and dangerous. 

18-gauge brads are so darn thin, they have a tendency to deflect whenever they encounter something hard, like a knot. In most cases, blowout is caused by the wood’s uneven cellular structure, so you can take steps to limit its occurrence. 

• Orient the brad correctly. If you’re attaching a face frame, hold your nailer so its handle is perpendicular to the outside edge (not parallel, as shown in the photo). This positions the brad’s wedge-shaped tip so any side-to-side deflection will be contained in the wood. 

• Fire into the face frame’s growth rings. Check the end grain. 

If your firing angle parallels the growth rings, the brad will simply deflect off the hard latewood. 

• Increase the air pressure when you nail into hard wood. Just like a putt that falls off line when it loses speed, a brad driven softly is more likely to deflect. 

• Protect yourself. Even when you take preventative safety precautions, blowout can still occur. Always wear eye protection and keep your fingers well away from the brad’s path.


Avoid Nailer Elbow

A stiff, unwieldy air hose makes your nailer hard to maneuver, especially in tight spots. This swiveling air plug ($9 for 1/4-in. hose; $10 for 3/8-in. hose) increases your range of movement by acting as a stress-relieving universal joint between your nailer and hose (see Sources, below).


18-Gauge Brads are Interchangeable

Argh! You’re all out of brads. The owner’s manual says “USE OUR BRADS ONLY!,” but the store doesn’t carry the right brand for your nailer. What to do? 

If you’re in this pickle, don’t worry about the brand. The shafts of all 18-gauge brads are essentially the same size. Just make sure the brads you buy are the right length. Most owner’s manuals list the lengths that’ll fit, but here’s how to be sure: On the side of your nailer’s magazine is a series of flutes that correspond to the different brad lengths it accepts. To fit, the brad clip must sit on the steel wear strip at the bottom of the magazine and the brad heads have to rest between the flutes. Brad strips that hang from the flutes without bottoming on the wear strip don’t fit. They’ll cause misfires, jams and/or premature wear. 


Don’t Hammer Your Nailer

High air pressure is hard on your nailer. It’ll wear out the O-rings and other internal components prematurely.

Click here to read the rest of the article from American Woodworker