American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Master Your Mortiser Yankton SD

To create perfect mortises, the chisel must be parallel to the fence. It’s easiest to place a board against the fence, move the fence forward and pivot the chisel until its face is flush with the board.

Ace Hardware
(605) 260-2813
2404 Broadway Ave, Across the street from Bonanza
Yankton, SD
 
Kmart 4813 / Cross Merch
(605) 665-8025
2210 Broadway Ave
Yankton, SD
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Carhart Lumber Co.
(402) 254-3928
119 E Main
Hartington, NE
 
The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Dakota Farm And Ranch Sup
(605) 765-9400
30960 Us Highway 212
Gettysburg, SD
 
Yankton - Auth Hometown
(605) 665-7861
2901 Broadway Ave
Yankton, SD
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

Fullerton Lumber Co 938
(605) 665-9651
2409 Broadway Ave
Yankton, SD
 
Kruse True Value
(402) 254-3840
207 N Summit Ave
Hartington, NE
 
Rbp Supply
(605) 856-4000
708 E Todd Street
Mission, SD
 
Homestead Building Supplies
(605) 692-6191
823 S Main Avenue
Brookings, SD
 

Master Your Mortiser

Master Your Mortiser

Shop-tested techniques guarantee great results

by George Vondriska

The first time I used my benchtop mortiser was almost my last. It was tedious to set up, difficult to operate and my results stunk. But now the mortiser is my first choice whenever I have mortises to cut. It turns out the problem wasn’t the machine—in fact, the newest benchtop mortisers do a great job. Instead, the problem was my inexperience. I discovered there’s a learning curve to successfully setting up and operating a mortiser. 

Read on to learn the techniques I use to get consistent, professional-quality results from my mortiser. If you follow these methods and mortising is still a struggle, your machine’s fence and hold-down may need tuning. 

The hollow chisel and auger bit work together to cut square mortises. The auger drills a hole and then the chisel squares the corners. Chips produced while cutting are lifted by the auger and ejected through holes in the chisel. 

Start Sharp, Stay Sharp

You’ll get better results with less effort if you take a few minutes to sharpen your bit and chisel before each use.

Sharpen the auger’s flutes with a small auger file (this one’s from Nicholson’s miniature file set #42030, about $17 at Amazon.com). An auger file has smooth edges that won’t harm adjacent surfaces during close work. Hold the file flat on the bevel and move it forward only, toward the cutting edge.

Sharpen the chisel’s inside bevels with a round slipstone (about $15 at woodworking specialty stores).

Hone the outside faces on a flat stone, using even pressure and a circular motion.

Insert a DIme to Install the Bits

To work properly, the auger must slightly project beyond the hollow chisel. Here’s an easy way to achieve the perfect projection. Temporarily install the chisel with a dime squeezed between its shoulder and the machine. Then lock the auger in position with the edge of its cutting flute even with the chisel’s tips. Remove the dime, slide the chisel’s collar tight to the machine and lock it.

Instantly Align the Chisel

To create perfect mortises, the chisel must be parallel to the fence. It’s easiest to place a board against the fence, move the fence forward and pivot the chisel until its face is flush with the board. 

Arches Set the Depths of Cut

Mark the tenon’s length on the end of the workpiece. Then lower the chisel. Lock the depth-of-cut stop when the tops of the chisel’s arches are even with your line. This method assures that your tenons will seat properly, because it automatically creates a mortise that’s slightly deeper than the tenon’s length. 

Stay Cool

Make life easier for the chisel and auger by spritzing them with cutting lubricant before each use.

Click here to read the rest of the article from American Woodworker