American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Miter Saws De Soto MO

T-track makes the stop easy to install and adjust. When the stop isn't necessary, tightening the knobs draws the bolts into the counterbored holes, so they don't protrude.

The Home Depot
(636)937-9601
1131 W Gannon
Festus, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Dep Builders Supply/dep Heating & Cooling
(636) 337-3381
12561 Hwy 21
De Soto, MO
 
LOWE'S OF FESTUS, MO
636 933-3320
1111 BRADLEY STREET FESTUS, MO, 63028
Festus, MO
 
Lowe's
(636) 933-3320
1111 Bradley Street
Festus, MO
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Crystal City - Dlr In Kmart
(636) 933-7011
155 Twin City Mall
Crystal City, MO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-22
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-22

Hamel & Rowe Inc
(636) 586-3230
210 N Main St
De Soto, MO
 
Hopson Lumber Company
(636) 586-3311
918 South Main Street
De Soto, MO
 
Festus Do it center
(636) 937-9663
1198 Shapiro Dr
Festus, MO
 
Holekamp Do it center
(573) 358-3371
317 N Division
Bonne Terre, MO
 
ABC Supply Co.,Inc./Herculaneum
636-937-9150
1538 Industrial Dr Herculaneum, MO, 63048
Herculaneum, MO
 

Miter Saws

Miter Saws

Whether you're building furniture, cutting trim molding or framing a garage, a compound miter saw is an indispensable tool. It can swivel left or right to make a standard miter and tilt to make a compound cut. Miter saws are capable of both rough and precision work. But no matter what you're doing, hitting your marking line right on the nose has always been a problem. Help is on the way. An accurate laser shows you exactly where the cut will go (Photo 1). A laser just might save you from a careless accident, too. As a fellow woodworker put it, “If the red line is shining on your hand, don't cut!”

PHOTO 1:
The glowing red line of a laser is the latest innovation in miter saws. It's supposed to show you exactly where the blade will cut, but some lasers work better than others. This one is top-notch!

PHOTO 2:
Accurate cuts are no problem at the pre-set angles on any saw. The catch is that you must be picky about aligning the fence to the blade when you first set up the saw.

PHOTO 3:
Tilting and rotating a miter saw allows you to make a right-angle joint with a wide piece of crown molding. Many saws have a detent at 31.6 degrees for making this cut.

PHOTO 4:
Saws with tall fences and stops are best for cutting crown molding in an upright position. This is a more intuitive method than laying the molding flat because the blade isn't tilted. However, with many saws you must rig up a tall wooden fence for it to work.

10-Inch vs. 12-Inch Saws
Most miter saws come with 10-in. or 12-in.-diameter. blades. (Some saws take 8-in. blades, but we didn't test any of those. We also excluded a few saws that can't tilt.) Both sizes share the same general features, but there are major differences: Capacity. Using construction lumber as a rough guide, a 10-in. saw can crosscut and bevel 4x4s and 2x6s. To handle 2x8s and wide crown molding you have to move up to a 12-in. saw. Price. There's a huge difference. 10-in. saws start at about $100; 12-in. at $250. Weight. A 12-in. saw can weigh twice as much as a 10 in. Your back will know the difference if you have to lug the machine around a lot. 10 & 12 in Saws info

PHOTO 5:
Saws that tilt left and right are handy in a crowded shop, where you don't have equal room on either side of the machine. Dual-bevel saws also have better sight lines on both sides of the blade because the motor is out of the way. That's particularly helpful for lefties.

PHOTO 6:
A flat, easy-to-read scale with a thin, hairline cursor gets a big thumbs up. Miter saws kick up
a lot of dust, but
flat scales are easy to wipe clean. We prefer a cursor that's out
in the open, where
no shadows can obscure it.

PHOTO 7:
Hold-downs improve safety and accuracy. An easy-to-use hold-down eliminates the need to put your fingers near the bla...

Click here to read the rest of the article from American Woodworker