American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Mobile Miter Saw Stand Mitchell SD

I went all-out on my stand, adding my favorite bells and whistles. The cost is about $500 without the saw or vacuum. That’s a lot of dough, but you can slash the cost to $210 by eliminating the commercial fence parts, using less expensive plywood with no edge-banding, dropping the drawers, doors and dust hood and doing without the tool-actuated switch.

Thune True Value Hardware
(605) 996-7508
1400 N Main St
Mitchell, SD
 
Mitchell - Auth Hometown
(605) 995-0090
1801 N Main St Unit 8B
Mitchell, SD
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:11-16
Store Features
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:11-16

The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Redfield True Value
(605) 472-1131
525 N Main St
Redfield, SD
 
Fastenal- Aberdeen
605-226-8238
6 Nth Dakota Street Suite 100 Aberdeen, SD, 57401
Aberdeen, SD
 
Kmart 4735 / Cross Merch
(605) 996-0984
1313 S Burr St
Mitchell, SD
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0
Store Features
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0

Thune True Value Hardware
(800) 642-7392
1400 N Main St
Mitchell, SD

Data Provided by:
Chester Hardware, Inc.
(605) 489-2121
402 4th St
Chester, SD
 
Nyberg's Ace Hardware
(605) 362-4223
7210 W 41st St
Sioux Falls, SD
 
Dakota Ace Hardware
(605) 766-5097
106 Main, Downtown Viborg
Viborg, SD
 
Data Provided by:

Mobile Miter Saw Stand

Mobile Miter Saw Stand

Get more from your miter saw with a stand that handles everything.

by Richard Tendick

I went all-out on my stand, adding my favorite bells and whistles. The cost is about $500 without the saw or vacuum. That’s a lot of dough, but you can slash the cost to $210 by eliminating the commercial fence parts, using less expensive plywood with no edge-banding, dropping the drawers, doors and dust hood and doing without the tool-actuated switch.

Folding Wings

Cursor and Flip Stop

Removable Saw Platform

Dust-Collection Hood

On-Board Vacuum

Sturdy Casters

Multi-Position Fences

You can move the fences on this stand to three different positions, depending on the job. The fences are clamped to the stand’s tables by threaded knobs. A pair of steel locating pins pass through a support behind each fence and into a series of holes drilled into the stand’s top (see photo, below). This automatically indexes the fence to two of the three positions. 

For most cuts, you can line up each of the extension fences with the saw’s fence.

For making cuts with no tear-out on the back side or for cutting very short pieces, you can move the extension fence forward to align with a zero-clearance fence.

When you make a compound miter cut, push the extension fences back so you can slide the saw’s fence to the left (see photo, below). It’s also a good idea to push the fences back for cutting slightly bent or crooked stock.

Make the Boxes, Cabinet and Wings

1. Measure your saw to determine the size of the stand’s well. If needed, adjust the sizes of the drawer boxes and cabinet in the Cutting List (page 76). Cut all the plywood pieces to size (Fig. D, below).

2. Cut 1/4-in. strips of solid wood to edge-band the sides of the boxes’ tops (B2). Glue on the banding.

3. Cut dados and rabbets in the parts for the boxes and cabinet (A1, A2, B1, B2, B3, B4) (Detail 2, below). Note that a drawer box’s top (B2) overhangs its sides (B1, Detail 1, page 74). This overhang provides clearance for the wing’s prop (B8) to fold against the cabinet’s side. Assemble the boxes and cabinet. Glue and screw the spacers (B5) to the boxes. The spacers bring the inside of the drawer box flush to the face frame, which will be attached later.

4. Glue the double-thickness wings (B7). Lay the parts on your tablesaw’s top and weight them with cinder blocks to apply clamping pressure. Trim the wings to final size.

5. Cut strips to band the wings, doors (D), drawer faces (C4), saw platform (E1), shelf (A5), dust-hood sides (F1) and dust-hood top (F2). Glue on the banding.

6. Cut out the wing props (B8, Fig. B, below). Glue material to make the hinge spacers (B6). Cut them to final size and glue and screw them to the boxes.

7. Cut the continuous hinge into four 14-in. lengths. Place the boxes upside down on a flat sur...

Click here to read the rest of the article from American Woodworker