American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Modular Shop Cabinets Brookings SD

These modular shop cabinets function in much the same way. Designed for ample storage, they also form a stunning piece of cabinetry. Make no mistake, though; these cabinets are firmly rooted in modern cabinet making techniques.

Brookings Rent-All
(605) 697-5544
803 Main Avenue South
Brookings, SD
 
Fastenal- Brookings
605-697-6631
1321 Main Avenue South Brookings, SD, 57006
Brookings, SD
 
Homestead Building Supplies
(605) 692-6191
823 S Main Avenue
Brookings, SD
 
J & K Building Center
(605) 997-3714
110 S Wind
Flandreau, SD
 
Fullerton Lumber Co 812
(605) 624-2655
113 West Main St.
Vermillion, SD
 
Lowe's of Brookings
605-696-2730
812 25th Ave Brookings, SD, 57006
Brookings, SD
 
Ace Hardware
(605) 697-5223
710 22nd Ave S, Brookings Mall
Brookings, SD
 
Lowe's
(605) 696-2730
812 25Th Avenue
Brookings, SD
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Fastenal- Sioux Falls
605-368-9859
27074 Henry Pl. Sioux Falls, SD, 57108
Sioux Falls, SD
 

Modular Shop Cabinets

Modular Shop Cabinets



In days gone by, apprentice cabinetmakers used to build their own tool chests. The chests were often works of art that both displayed theowner's level of craftsmanship and provided practical storage for tools. These modular shop cabinets function in much the same way. Designed for ample storage, they also form a stunning piece of cabinetry. Make no mistake, though; these cabinets are firmly rooted in modern cabinetmaking techniques. They're built using the same modular construction system today's professionals prefer. After you've warmed up on these shop cabinets, you'll be ready to tackle making a whole kitchen full using the same technique.

These cabinets are built with box or modular construction: All the units are simply 2-ft.-wide butt-joined boxes. Because  the boxes are all the same width, the drawers and doors are, too. This stream lines machining and assembly. Each box or cabinet is installed one at a time, allowing one person to build and install a run of cabinets of almost any length.

Project Requirements at a Glance
Material:
30 bd. ft. of 4/4 birch
5 bd. ft. of 5/4 cherry
Five sheets of 3/4-in. x 4-ft. x 8-ft. birch plywood
One sheet of 1/2-in. x 4-ft. x 8-ft. birch plywood
Three sheets of 1/4-in. x 4-ft. x 8-ft. birch plywood
Three sheets of 1/2-in. x 5-ft. x 5-ft. Baltic birch plywood
One sheet of 3/4-in. x 49-in. x 97-in. MDF
Two quarts of oil finish or varnish

Tools:

Edge-tape trimming tools, clothes iron, table saw with dado blade, router and router table, bandsaw, drill press, belt sander, finish sander, 18-gauge nail gun, 35-mm drill bit and level Hardware: 15 pairs of drawer slides, eight Euro/cup hinges, four pneumatic door-closing cushions, two 24-in. under-cabinet lights Total Cost: $1,100 for a6-ft. run

Extra Features

These are “dream” shop cabinets, and to keep the dream alive, I've jammed them full of extra features:
- Fifteen full-extension drawers with 1-in. over travel and a self-closing feature that takes over when the drawer is nearly closed(a welcome feature when you have your hands full).
- Angled shelves that put frequently used tools right at your fingertips.
- Shop-made handles that double as label holders.
- A worktop shelf that works like an elevated tool tray.
- A durable worktop that overhangs the lower cabinets to allow clamping to the surface.



PHOTO 1:

All the visible cabinet edges are covered with iron-on edge tape, which goes on fast and looks great. Trim the tape with a double-sided edge trimmer. Cut the tape ends flush to the plywood prior to trimming.

PHOTO 2:
Cut grooves in the upper cabinet sides to house the metal shelf supports. When installed, the standards stand proud of the grooves by about 1/16 in.



PHOTO 3:

Assemble the boxes using a support tube to hold the top and bottom steady. The support tube for the upper cabinets is just an 8 x 8 x22-in. ...

Click here to read the rest of the article from American Woodworker