American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Mortising on the Drill Press Minot ND

Mortising attachments are available for almost every drill press.Although they vary in appearance, they all have three basic components:a fence, a chisel holder and a hold-down. Upgrading these parts tostabilize the workpiece and operating the drill press at the optimalspeed are the keys to success.

Minot - D
(701) 852-4175
1 20Th Ave Se
Minot, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

ACME TOOLS- Minot
(701) 839-2263
700 20th Ave SE Minot, ND, 58701
Minot, ND
 
Fastenal- Minot
701-839-7566
700 20th Ave SW Minot, ND, 58701
Minot, ND
 
Arrowhead Ace Hardware
(701) 839-6166
1600 2nd Ave SW
Minot, ND
 
Kmart 9600 / Cross Merch
(701) 251-1111
2400 Us-281 S
Jamestown, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Dakota Sq Mall
(701) 857-1223
2400 10Th St Sw
Minot, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18

Muus Lumber & Hardware
(701) 852-4038
2700 Burdick Expressway E
Minot, ND
 
Enerbase
(701) 852-2501
215 Central Ave E
Minot, ND
 
The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Williston True Value
(701) 572-7300
10 E 26th Street
Williston, ND
 

Mortising on the Drill Press

Mortising on the Drill Press



Even though they're sexy, benchtop mortising machines aren't the onlypower-tool option when it comes to cutting square-shouldered mortises.A drill-press mortising attachment can be just as effective and itcosts a lot less: $30 to $80 instead of $200 or more. I'll show you howto tune any out-of-the-box mortising attachment so it's easy to installand a joy to use.

Mortising attachments are available for almost every drill press.Although they vary in appearance, they all have three basic components:a fence, a chisel holder and a hold-down. Upgrading these parts tostabilize the workpiece and operating the drill press at the optimalspeed are the keys to success.

I get first-class results with my tuned-up mortising attachment. Thatmeans I don't have to store a large, heavy mortiser that I would onlyuse occasionally. On the drill press, I can slow the speed way down,too, so I don't overheat my bits. Drill-press mortising is slower, butit's much more pleasant, a lot quieter and much less nerve-wrackingthan using a mortiser.

Square mortises require special bits, which can be bought individuallyor in sets. Bits range in price from $10 to more than $50 apiece.Inexpensive bits usually won't stay sharp as long (see "Start Sharp,Stay Sharp," page 5), but dropping one on the concrete floor won't giveyou a heart attack, either.


Two-piece mortising chisels cut square holes. The auger bit fits inside the chisel and protrudes slightly.


During operation, the augerdrills a round hole and the four-sided chisel squares the corners. Cutside by side, square holes create mortises (see photo below).
1. Slow down.
Mortising chiselswork best at slow speeds, between 1,000 rpm and 1,500 rpm, depending onthe mortise size and the wood density. Within this range, use trial anderror to find the speed that works best.
2. Mount
the mortising fence ona separate base, rather than fastening it directly to the drill-presstable. Then clamp the base to the drill-press table. This setup makesthe fence easy to adjust, so positioning the workpiece is a breeze. 3. Install
the chisel and bit.The chisel holder, which clamps on to the quill, centers the chiseldirectly beneath the chuck. Lock the chisel with its collar tightlyagainst the holder. Then slide the bit into the chuck.
4. Leave
a gap. Position theauger bit with its cutting head about 1/16 in. away from the domedinside surface of the hollow chisel. Don't jam these two partstogether. This gap is essential, because it allows shavings cut by theauger to be lifted into the hollow chisel and ejected. If the gap istoo small or too large, the trapped shavings will bind the bit.
5. Lubricate
the auger bit aftermaking sure it spins freely inside the chisel.

Click here to read the rest of the article from American Woodworker