American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Mortising on the Drill Press Petersburg VA

Mortising attachments are available for almost every drill press.Although they vary in appearance, they all have three basic components:a fence, a chisel holder and a hold-down. Upgrading these parts tostabilize the workpiece and operating the drill press at the optimalspeed are the keys to success.

The Home Depot
(804)520-0402
2600 Conduit Rd
Colonial Heights, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Thacker Ace Hardware
(804) 861-6700
3671 S Crater Rd, Wal-Mart On S. Crater Road
Petersburg, VA
 
Southpark Mall
(804) 524-3255
114 Southpark Cir
Colonial Hts, VA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:8-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:8-21
Sun:11-18

Lowe's
(804) 957-6201
2085 Waterside Drive
Prince George, VA
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Lowe's
(804) 768-8843
2601 Weir Place
Chester, VA
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(804)706-4501
12300 Jefferson Davis Hw
Chester, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 3869 / Cross Merch
(804) 520-5146
116 Southgate Square
Colonial Heig, VA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

LOWE'S OF CHESTER, VA.
804 768-8843
2601 WEIR PLACE CHESTER, VA, 23831
Chester, VA
 
Kmart 3868 / Cross Merch
(804) 748-6108
12810 Jefferson Davis Hwy
Chester, VA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Pleasants Hardware
(804) 275-7002
5140 Jefferson Davis Hwy
Richmond, VA
 

Mortising on the Drill Press

Mortising on the Drill Press



Even though they're sexy, benchtop mortising machines aren't the onlypower-tool option when it comes to cutting square-shouldered mortises.A drill-press mortising attachment can be just as effective and itcosts a lot less: $30 to $80 instead of $200 or more. I'll show you howto tune any out-of-the-box mortising attachment so it's easy to installand a joy to use.

Mortising attachments are available for almost every drill press.Although they vary in appearance, they all have three basic components:a fence, a chisel holder and a hold-down. Upgrading these parts tostabilize the workpiece and operating the drill press at the optimalspeed are the keys to success.

I get first-class results with my tuned-up mortising attachment. Thatmeans I don't have to store a large, heavy mortiser that I would onlyuse occasionally. On the drill press, I can slow the speed way down,too, so I don't overheat my bits. Drill-press mortising is slower, butit's much more pleasant, a lot quieter and much less nerve-wrackingthan using a mortiser.

Square mortises require special bits, which can be bought individuallyor in sets. Bits range in price from $10 to more than $50 apiece.Inexpensive bits usually won't stay sharp as long (see "Start Sharp,Stay Sharp," page 5), but dropping one on the concrete floor won't giveyou a heart attack, either.


Two-piece mortising chisels cut square holes. The auger bit fits inside the chisel and protrudes slightly.


During operation, the augerdrills a round hole and the four-sided chisel squares the corners. Cutside by side, square holes create mortises (see photo below).
1. Slow down.
Mortising chiselswork best at slow speeds, between 1,000 rpm and 1,500 rpm, depending onthe mortise size and the wood density. Within this range, use trial anderror to find the speed that works best.
2. Mount
the mortising fence ona separate base, rather than fastening it directly to the drill-presstable. Then clamp the base to the drill-press table. This setup makesthe fence easy to adjust, so positioning the workpiece is a breeze. 3. Install
the chisel and bit.The chisel holder, which clamps on to the quill, centers the chiseldirectly beneath the chuck. Lock the chisel with its collar tightlyagainst the holder. Then slide the bit into the chuck.
4. Leave
a gap. Position theauger bit with its cutting head about 1/16 in. away from the domedinside surface of the hollow chisel. Don't jam these two partstogether. This gap is essential, because it allows shavings cut by theauger to be lifted into the hollow chisel and ejected. If the gap istoo small or too large, the trapped shavings will bind the bit.
5. Lubricate
the auger bit aftermaking sure it spins freely inside the chisel.

Click here to read the rest of the article from American Woodworker