American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Nesting Trays Van Wert OH

Prepare your stock, including extra pieces for test-cutting. Cut blanks for the ends (A1, B1 and C1, Fig. A, page 67) and sides (A2, B2 and C2) to length, but leave them 1/8 in. oversize in width. All the ends must be squarely cut.

Van Wert - Auth Hometown
(419) 232-4900
1159 S Shannon St
Van Wert, OH
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8.5-18
Tue:8.5-18
Wed:8.5-18
Thu:8.5-18
Fri:8.5-18
Sat:9-18
Sun:11-16
Store Features
Mon:8.5-18
Tue:8.5-18
Wed:8.5-18
Thu:8.5-18
Fri:8.5-18
Sat:9-18
Sun:11-16

Lee's Ace Hardware
(419) 238-1546
647 W Ervin Rd
Van Wert, OH
 
Ottoville Do it center
(419) 453-3338
145 W 3rd Street
Ottoville, OH
 
Delphos Ace
(419) 692-0921
242 N Main St
Delphos, OH
 
Fastenal- Decatur
260-724-7093
1701 Patterson Street Decatur, IN, 46733
Decatur, IN
 
Fastenal- Van Wert
419-232-4350
529 Bonnewitz Avenue Van Wert, OH, 45891
Van Wert, OH
 
Hall Do it Best Lumber
(419) 749-2119
122 S Main St
Convoy, OH
 
Tri County Do it center
(419) 692-6936
833 N Main St
Delphos, OH
 
Decatur Ace Hardware
(260) 724-3700
1220 S 13th St, Located on US 27, Across from Baymont Inn
Decatur, IN
 
Kmart 3664 / Cross Merch
(260) 728-2010
804 S 13Th St
Decatur, IN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Nesting Trays

Nesting Trays

Eye-catching and practical, these handy carryalls are sure to please.

by Tim Johnson

Here’s your chance to cut lots of corners and still get great-looking results. These sturdy trays are easy to build, thanks to their simple box joints and template-routed curves. You don’t need a super-equipped shop, just a tablesaw with a dado set, a router table and a drill press. You’ve probably saved enough scrap pieces from other projects to build the trays and the jigs, but even if you buy lumber and plywood, you can make this trio of trays for less than $60. 

Cut the Box Joints

1. Prepare your stock, including extra pieces for test-cutting. Cut blanks for the ends (A1, B1 and C1, Fig. A, page 67) and sides (A2, B2 and C2) to length, but leave them 1/8 in. oversize in width. All the ends must be squarely cut.

2. Arrange the pieces for each box and then mark the bottom edge of every one. When you cut the box joints, these marks will correctly orient the pieces in the jig. 

3. Box-joint jigs index the workpiece for cutting sockets. (Photo 1). Cutting a series of sockets creates the pins. To make the joint, one piece has pins where the mating piece has sockets (see “ Tablesaw Box Joints ,”). 

4. Cut test box joints to dial in a precise fit. This is fussy work, because the tolerances are tiny. The pieces should slide together without binding or rattling. The best jigs have built-in adjustment systems. 

5. Cut all the box joints. On the end-piece blanks, cut sockets only as far as their curved profiles dictate. The side-piece blanks are oversize, so you’ll have to make an extra pass to complete the top sockets. 

Rout the Ends

6. Use the end profile of the large tray (A1, Fig. C, below) as a pattern when you make the routing jig (Fig. B, below). First, transfer the curved edge profile to the jig’s base. Then drill 1-in.-dia. holes with a Forstner bit to establish the ends of the handle hole. Finish rough-cutting the handle hole with a jigsaw. Then rough-cut the edge profile.

7. Smooth the edge profile using an oscillating spindle sander or a sanding drum in your drill press. Install a 3/4-in.-dia. spindle or drum to smooth the handle hole. 

8. Use a large end-piece blank to position the jig’s fence. Each end has six pins. Fasten the fence so the top pins are flush with the base’s curved profile.

9. Install the stops after centering the large end-piece blank. Mount the toggle clamps (see Sources, below).

10. Draw edge profiles and handle holes on all the end blanks after installing them in the jig. Make spacers (W, X, Y and Z, Fig. B) to position the medium and small blanks. 

11. Rough-saw all the curved profiles about 1/16 in. away from the pattern lines. To rough out the handle holes, drill 7/8-in.-dia. holes and use a jigsaw to saw out the waste.

12. Rout the edge profiles with a top-bearing flush-trim bit (Photo 2).

Click here to read the rest of the article from American Woodworker