American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Perfect Butt Joints in Laminate Gadsden AL

It's easy to get professional-looking results with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate.

Gadsden Mall
(256) 543-4900
1001 Rainbow Dr
Gadsden, AL
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

LOWE'S OF GADSDEN, ALA.
256 543-1543
615 GEORGE WALLACE DRIVE GADSDEN, AL, 35903
Gadsden, AL
 
Fastenal-Attalla
256-570-0238
84 Industrial Blvd Attalla, AL, 35954
Attalla, AL
 
Warren Ace Hardware
(256) 435-6383
1420 Pelham Rd S, Joy Christian Book Store
Jacksonville, AL
 
R & R Hardware
(256) 447-6044
105 S Main St
Piedmont, AL

Data Provided by:
Kmart 4475 / Cross Merch
(256) 547-5703
201 George Wallace Dr
Gadsden, AL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Lowe's
(256) 543-1543
615 George Wallace Drive
Gadsden, AL
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Weathers Hardware & Appliance
(256) 593-4218
202 W Mill Ave, Hwy. 205 and Hwy. 168 Crossing
Boaz, AL
 
Kmart 4835 / Cross Merch
(256) 927-8000
1525 Chestnut Byp
Centre, AL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Whitley Hardware
(205) 466-3033
86343 US Hwy 278
Altoona, AL

Data Provided by:
Data Provided by:

Perfect Butt Joints in Laminate

Perfect Butt Joints in Laminate

An Underscribe Router Attachment Guarantees Success

by Brad Holden

Long countertops or those that turn corners need butt joints. You can use several methods to make this joint, but the easiest way to get tight-fitting, professional-

looking results is with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate (see Fig. A, below).

1. Start by making a couple of small (approximately 12-in. x 12-in.) test countertops from scraps of the same laminate you will use in your finished project. Using the same kind of laminate is important, because even a small difference in laminate thickness will affect the accuracy and fit of the final joint. Use the test countertops and Steps 2 through 9, to set up the underscribe attachment. Rout an inch or two on one of the test tops, check the fit and adjust the underscribe base as necessary. The base has built-in micro-adjusters, so fine-tuning is simple. When you have the perfect fit, run one more test cut using the entire joint on one of the test countertops. You will only get one shot at your project, so now is the time to fine-tune the attachment to perfection. 

2. Rout a straight edge on one piece of laminate (Photo 1). You’ll end up with a small burr on the bottom edge of the laminate. Remove the burr with a file, so the laminate will glue down completely flat. Mark a straight pencil line along this straight edge. The lip on the underscibe attachment rides on this edge and guides the router through the cut. As a result, this first piece of laminate is called the guide piece. Mark the adjoining edge on the second piece of laminate with a wavy line to show that it has a rough edge (Photo 2).

3. Position the guide piece on the substrate without adhesive and make a pencil line on the substrate along the laminate’s straight edge. Next, lay down the second piece, overlapping the guide piece by 1/4 in. to 3/4 in. Use pieces of masking tape to mark this overlap.

4. Remove the laminate pieces from the substrate and apply adhesive to all parts.

5. Reapply the guide piece of laminate, making sure it lines up with the pencil mark you traced onto the substrate in Step 3. Use spacer sticks to prevent it from sticking until you have the laminate aligned. Pull out one stick at a time, starting with the edge closest to the pencil line. Use a laminate roller to make sure the laminate is thoroughly pressed down.

6. Apply the overlap piece using the same method. Line it up with the tape on the guide piece, remove the spacer sticks, and roll it down. Roll as close to the seam as you can. This helps prevent chips from getting under the laminate when you rout the seam. Also, a vacuum attachment is available for the underscribe attachment. It removes alm...

Click here to read the rest of the article from American Woodworker