American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Perfect Butt Joints in Laminate La Follette TN

It's easy to get professional-looking results with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate.

Lowe's- La Fallette
423-563-6020
2444 Jacksboro Pike La Follette, TN, 37766
La Follette, TN
 
Smith Ace Hardware
(423) 562-7738
116 E Central Ave
La Follette, TN
 
Affordable Ace Hardware Inc
(865) 992-5867
2603 Maynardville Hwy
Maynardville, TN
 
Kmart 9758 / Cross Merch
(865) 457-1115
190 Clinch Av
Clinton, TN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Claxton True Value Hardware
(800) 642-7392
610 Edgemoor Rd
Powell, TN

Data Provided by:
Lowe's
(423) 563-6020
2444 Jacksboro Pike
La Follette, TN
Hours
M-SA 7 am - 9 pm
SU 9 am - 8 pm

Lafollette - Auth Hometown
(423) 562-7700
2221 Jacksboro Pike
Lafollette, TN
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:13-18
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:13-18

Ace - T.V. Hardware
(865) 457-1478
356 Market St
Clinton, TN
 
WT Products
211 Newcomb Loop Rd
Newcomb, TN

Data Provided by:
The Home Depot
(615)731-2900
1155 Bell Rd
Antioch, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Perfect Butt Joints in Laminate

Perfect Butt Joints in Laminate

An Underscribe Router Attachment Guarantees Success

by Brad Holden

Long countertops or those that turn corners need butt joints. You can use several methods to make this joint, but the easiest way to get tight-fitting, professional-

looking results is with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate (see Fig. A, below).

1. Start by making a couple of small (approximately 12-in. x 12-in.) test countertops from scraps of the same laminate you will use in your finished project. Using the same kind of laminate is important, because even a small difference in laminate thickness will affect the accuracy and fit of the final joint. Use the test countertops and Steps 2 through 9, to set up the underscribe attachment. Rout an inch or two on one of the test tops, check the fit and adjust the underscribe base as necessary. The base has built-in micro-adjusters, so fine-tuning is simple. When you have the perfect fit, run one more test cut using the entire joint on one of the test countertops. You will only get one shot at your project, so now is the time to fine-tune the attachment to perfection. 

2. Rout a straight edge on one piece of laminate (Photo 1). You’ll end up with a small burr on the bottom edge of the laminate. Remove the burr with a file, so the laminate will glue down completely flat. Mark a straight pencil line along this straight edge. The lip on the underscibe attachment rides on this edge and guides the router through the cut. As a result, this first piece of laminate is called the guide piece. Mark the adjoining edge on the second piece of laminate with a wavy line to show that it has a rough edge (Photo 2).

3. Position the guide piece on the substrate without adhesive and make a pencil line on the substrate along the laminate’s straight edge. Next, lay down the second piece, overlapping the guide piece by 1/4 in. to 3/4 in. Use pieces of masking tape to mark this overlap.

4. Remove the laminate pieces from the substrate and apply adhesive to all parts.

5. Reapply the guide piece of laminate, making sure it lines up with the pencil mark you traced onto the substrate in Step 3. Use spacer sticks to prevent it from sticking until you have the laminate aligned. Pull out one stick at a time, starting with the edge closest to the pencil line. Use a laminate roller to make sure the laminate is thoroughly pressed down.

6. Apply the overlap piece using the same method. Line it up with the tape on the guide piece, remove the spacer sticks, and roll it down. Roll as close to the seam as you can. This helps prevent chips from getting under the laminate when you rout the seam. Also, a vacuum attachment is available for the underscribe attachment. It removes alm...

Click here to read the rest of the article from American Woodworker