American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Perfect Butt Joints in Laminate San Angelo TX

It's easy to get professional-looking results with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate.

The Home Depot
(325)223-0439
4363 Houston Harte Exwy
San Angelo, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- San Angelo
325-486-1626
701 Knickerbocker Rd San Angelo, TX, 76903
San Angelo, TX
 
Westlake Ace Hardware
(325) 942-6602
1821 Knickerbocker Rd
San Angelo, TX
 
Lowe's
(325) 942-3100
5301 Sherwood Way
San Angelo, TX
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(281)356-2087
6119 Fm 1488
Magnolia, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Southern Fastening Systems- San Angelo
915-944-8091
922 Arroyo Drive San Angelo, TX, 76903
San Angelo, TX
 
Angelo Bolt & Industrial Supply
325-655-0075
808 Warehouse Road San Angelo, TX, 76903
San Angelo, TX
 
Sunset Mall
(325) 942-5281
4000 Sunset Mall
San Angelo, TX
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

LOWE'S OF SAN ANGELO, TEX.
325 942-3100
5301 SHERWOOD WAY SAN ANGELO, TX, 76904
San Angelo, TX
 
The Home Depot
(214)654-9939
6110 Lemmon Ave
Dallas, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Perfect Butt Joints in Laminate

Perfect Butt Joints in Laminate

An Underscribe Router Attachment Guarantees Success

by Brad Holden

Long countertops or those that turn corners need butt joints. You can use several methods to make this joint, but the easiest way to get tight-fitting, professional-

looking results is with an underscribe attachment on a trim router. The term underscribe refers to the attachment riding under the piece being scribed. The cut is guided by a small lip on the underside of the attachment that follows the straight edge on the bottom piece of laminate (see Fig. A, below).

1. Start by making a couple of small (approximately 12-in. x 12-in.) test countertops from scraps of the same laminate you will use in your finished project. Using the same kind of laminate is important, because even a small difference in laminate thickness will affect the accuracy and fit of the final joint. Use the test countertops and Steps 2 through 9, to set up the underscribe attachment. Rout an inch or two on one of the test tops, check the fit and adjust the underscribe base as necessary. The base has built-in micro-adjusters, so fine-tuning is simple. When you have the perfect fit, run one more test cut using the entire joint on one of the test countertops. You will only get one shot at your project, so now is the time to fine-tune the attachment to perfection. 

2. Rout a straight edge on one piece of laminate (Photo 1). You’ll end up with a small burr on the bottom edge of the laminate. Remove the burr with a file, so the laminate will glue down completely flat. Mark a straight pencil line along this straight edge. The lip on the underscibe attachment rides on this edge and guides the router through the cut. As a result, this first piece of laminate is called the guide piece. Mark the adjoining edge on the second piece of laminate with a wavy line to show that it has a rough edge (Photo 2).

3. Position the guide piece on the substrate without adhesive and make a pencil line on the substrate along the laminate’s straight edge. Next, lay down the second piece, overlapping the guide piece by 1/4 in. to 3/4 in. Use pieces of masking tape to mark this overlap.

4. Remove the laminate pieces from the substrate and apply adhesive to all parts.

5. Reapply the guide piece of laminate, making sure it lines up with the pencil mark you traced onto the substrate in Step 3. Use spacer sticks to prevent it from sticking until you have the laminate aligned. Pull out one stick at a time, starting with the edge closest to the pencil line. Use a laminate roller to make sure the laminate is thoroughly pressed down.

6. Apply the overlap piece using the same method. Line it up with the tape on the guide piece, remove the spacer sticks, and roll it down. Roll as close to the seam as you can. This helps prevent chips from getting under the laminate when you rout the seam. Also, a vacuum attachment is available for the underscribe attachment. It removes alm...

Click here to read the rest of the article from American Woodworker