American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Plumb Your Shop with Air Bessemer AL

Every article I read on plumbing air lines advised using either iron or copper. Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly.

The Home Depot
(205)781-0110
6405 Flintridge Drive
Fairfield, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Birmingham Area, AL
(205) 988-3600
220 Cahaba Valley Road
Pelham, AL

Data Provided by:
The Home Depot
(205)995-9357
4995 Hwy 280
Birmingham, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(205) 428-1024
1201 19Th Street North
Bessemer, AL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Fastenal- Bessemer
205-426-8046
1031 19th St N Bessemer, AL, 35020
Bessemer, AL
 
The Home Depot
(205)988-8141
3670 Galleria Circle
Birmingham, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(205)685-1837
3191 Pelham Pkwy
Pelham, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(205)595-7780
7001 Crestwood Blvd
Birmingham, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF BESSEMER, AL
205 428-1024
1201 19TH STREET NORTH BESSEMER, AL, 35020
Bessemer, AL
 
Hueytown Do it Best Hardware
(205) 491-1626
3284 Allison Bonnett Mem
Hueytown, AL
 
Data Provided by:

Plumb Your Shop with Air

Plumb Your Shop With AIr

Flexible Hose Saves Time and Money

by Richard Tendick

Moments after I tripped over the air hose and dropped an armload of boards, I decided it was time to plumb my shop for air.  I was tired of having 50 ft. of hose on the floor and dashing back to the compressor to adjust the line pressure. I knew a permanent system could deliver the right amount of air where and when I needed it—without a big hose snaked dangerously across the floor. 

Every article I read on plumbing air lines advised using either iron or copper.  Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly. 

Ultimately, I decided on a solution I had used many times in my 27 years as a manufacturing plant engineer. When installing printing presses and other large machines, I used rubber air hose as a flexible pipe to route compressed air in and through the equipment without having to do a lot of complicated plumbing.

That approach would certainly work with all the obstructions in my shop. I chose a rubber hose rated for 250 pounds per square inch (psi), plenty for my little pancake compressor. The 1/2-in. inside diameter meant no reduction in air pressure would occur along the length of the run.

(Click Image to Expand)


(Click Image to Expand)

This story originally appeared in  American Woodworker September 2006, issue #123.

Source information may have changed since the original publication date.

Source  

MSC Industrial Supply, (800) 645-7270, www.mscdirect.com

September 2006, issue #123

Purchase this back issue.

Click here to read the rest of the article from American Woodworker