American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Plumb Your Shop with Air Gig Harbor WA

Every article I read on plumbing air lines advised using either iron or copper. Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly.

The Home Depot
(253)851-9404
5120 Borgen Blvd
Gig Harbor, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(253)474-9600
7050 Tacoma Mall Blvd
Tacoma, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(253)538-7100
101 E 152nd Street
Tacoma, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

NW Wood
(253) 279-4618
14224 Bingham Ave E
Tacoma, WA

Data Provided by:
The Home Depot
(206)575-9200
6810 S 180th St
Tukwila, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Home Depot The
(253) 851-9404
5120 Borgen Blvd Nw Unit Main
Gig Harbor, WA
 
The Home Depot
(253)661-9200
1715 S 352nd St
Federal Way, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Edensaw Woods
(253) 216-1150
8032 South 194th Street
Kent, WA

Data Provided by:
Rockler Woodworking and Hardware #15
(206) 244-9161
345 Tukwila Parkway
Tukwila, WA

Data Provided by:
The Home Depot
(206)762-2126
7345 Delridge Way SW
Seattle, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Data Provided by:

Plumb Your Shop with Air

Plumb Your Shop With AIr

Flexible Hose Saves Time and Money

by Richard Tendick

Moments after I tripped over the air hose and dropped an armload of boards, I decided it was time to plumb my shop for air.  I was tired of having 50 ft. of hose on the floor and dashing back to the compressor to adjust the line pressure. I knew a permanent system could deliver the right amount of air where and when I needed it—without a big hose snaked dangerously across the floor. 

Every article I read on plumbing air lines advised using either iron or copper.  Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly. 

Ultimately, I decided on a solution I had used many times in my 27 years as a manufacturing plant engineer. When installing printing presses and other large machines, I used rubber air hose as a flexible pipe to route compressed air in and through the equipment without having to do a lot of complicated plumbing.

That approach would certainly work with all the obstructions in my shop. I chose a rubber hose rated for 250 pounds per square inch (psi), plenty for my little pancake compressor. The 1/2-in. inside diameter meant no reduction in air pressure would occur along the length of the run.

(Click Image to Expand)


(Click Image to Expand)

This story originally appeared in  American Woodworker September 2006, issue #123.

Source information may have changed since the original publication date.

Source  

MSC Industrial Supply, (800) 645-7270, www.mscdirect.com

September 2006, issue #123

Purchase this back issue.

Click here to read the rest of the article from American Woodworker