American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Plumb Your Shop with Air Kennesaw GA

Every article I read on plumbing air lines advised using either iron or copper. Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly.

The Home Depot
(770)421-1245
1655 Shiloh Road NW
Kennesaw, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)792-6858
2350 Dallas Hwy
Marietta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)591-8663
9037 Hwy 92, Suite 100
Woodstock, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(678)567-1161
1062 Richard D Sailors
Powder Springs, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)432-9930
2450 Cumberland Pkwy
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)917-8425
3355 Cobb Pkwy
Acworth, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)971-2470
3605 Sandy Plains Rd
Marietta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)977-9700
4101 Roswell Rd
Marietta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)438-9678
1200 E W Connector SW
Austell, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)439-0707
145 Depot Drive
Hiram, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Plumb Your Shop with Air

Plumb Your Shop With AIr

Flexible Hose Saves Time and Money

by Richard Tendick

Moments after I tripped over the air hose and dropped an armload of boards, I decided it was time to plumb my shop for air.  I was tired of having 50 ft. of hose on the floor and dashing back to the compressor to adjust the line pressure. I knew a permanent system could deliver the right amount of air where and when I needed it—without a big hose snaked dangerously across the floor. 

Every article I read on plumbing air lines advised using either iron or copper.  Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly. 

Ultimately, I decided on a solution I had used many times in my 27 years as a manufacturing plant engineer. When installing printing presses and other large machines, I used rubber air hose as a flexible pipe to route compressed air in and through the equipment without having to do a lot of complicated plumbing.

That approach would certainly work with all the obstructions in my shop. I chose a rubber hose rated for 250 pounds per square inch (psi), plenty for my little pancake compressor. The 1/2-in. inside diameter meant no reduction in air pressure would occur along the length of the run.

(Click Image to Expand)


(Click Image to Expand)

This story originally appeared in  American Woodworker September 2006, issue #123.

Source information may have changed since the original publication date.

Source  

MSC Industrial Supply, (800) 645-7270, www.mscdirect.com

September 2006, issue #123

Purchase this back issue.

Click here to read the rest of the article from American Woodworker