American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Plumb Your Shop with Air Littleton CO

Every article I read on plumbing air lines advised using either iron or copper. Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly.

The Home Depot
(720)344-7645
1200 Mayberry Road
Littleton, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)706-1500
8477 S Yosemite Ave
Lone Tree, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)799-9071
9401 E Arapahoe Rd
Greenwood Village, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)765-0400
500 S Santa Fe Dr
Denver, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(720)524-2480
860 S Colorado Blvd
Glendale, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)794-0352
3000 W Belleview Ave
Littleton, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)922-0444
3130 S Sheridan Blvd
Denver, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcraft - Denver, CO
(303) 290-0007
6770 S. Peoria St
Centennial, CO

Data Provided by:
Rockler Woodworking and Hardware #3
(303) 782-0588
2553 S. Colorado Blvd. Suite 108
Denver, CO

Data Provided by:
The Home Depot
(303)232-6303
6701 W Alameda Ave
Lakewood, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Data Provided by:

Plumb Your Shop with Air

Plumb Your Shop With AIr

Flexible Hose Saves Time and Money

by Richard Tendick

Moments after I tripped over the air hose and dropped an armload of boards, I decided it was time to plumb my shop for air.  I was tired of having 50 ft. of hose on the floor and dashing back to the compressor to adjust the line pressure. I knew a permanent system could deliver the right amount of air where and when I needed it—without a big hose snaked dangerously across the floor. 

Every article I read on plumbing air lines advised using either iron or copper.  Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly. 

Ultimately, I decided on a solution I had used many times in my 27 years as a manufacturing plant engineer. When installing printing presses and other large machines, I used rubber air hose as a flexible pipe to route compressed air in and through the equipment without having to do a lot of complicated plumbing.

That approach would certainly work with all the obstructions in my shop. I chose a rubber hose rated for 250 pounds per square inch (psi), plenty for my little pancake compressor. The 1/2-in. inside diameter meant no reduction in air pressure would occur along the length of the run.

(Click Image to Expand)


(Click Image to Expand)

This story originally appeared in  American Woodworker September 2006, issue #123.

Source information may have changed since the original publication date.

Source  

MSC Industrial Supply, (800) 645-7270, www.mscdirect.com

September 2006, issue #123

Purchase this back issue.

Click here to read the rest of the article from American Woodworker