American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Plumb Your Shop with Air Silsbee TX

Every article I read on plumbing air lines advised using either iron or copper. Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly.

The Home Depot
(409)892-4131
3910 Eastex Freeway
Beaumont, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

M & D Partners LLC
(409) 751-3600
122 S Main St, Across from Lumberton Middle School
Lumberton, TX
 
Ritter@Home
(409) 994-3587
379 Hwy 62
Buna, TX
 
LOWE'S OF BEAUMONT, TEX.
409 898-2200
4120 DOWLEN NO. BEAUMONT, TX, 77708
Beaumont, TX
 
Lowe's
(409) 898-2200
4120 Dowlen Road
Beaumont, TX
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Parker's Do it center-Silsbee
(409) 385-3729
1145 Hwy 96 South
Silsbee, TX
 
Keeler True Value
(409) 994-3501
269 Tx State Highway 62
Buna, TX
 
Ritter at Home
(409) 842-5410
7420 Hwy 105
Beaumont, TX
 
M & D Ace Hardware
(409) 769-0281
1230 N Main St
Vidor, TX
 
Parkdale Mall
(409) 898-9100
6461 Eastex Fwy
Beaumont, TX
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Plumb Your Shop with Air

Plumb Your Shop With AIr

Flexible Hose Saves Time and Money

by Richard Tendick

Moments after I tripped over the air hose and dropped an armload of boards, I decided it was time to plumb my shop for air.  I was tired of having 50 ft. of hose on the floor and dashing back to the compressor to adjust the line pressure. I knew a permanent system could deliver the right amount of air where and when I needed it—without a big hose snaked dangerously across the floor. 

Every article I read on plumbing air lines advised using either iron or copper.  Because my basement shop holds a lot of obstructions, using iron or copper would result in a whole lot of threading or soldering of short little pieces. Besides, copper and iron fittings are costly. 

Ultimately, I decided on a solution I had used many times in my 27 years as a manufacturing plant engineer. When installing printing presses and other large machines, I used rubber air hose as a flexible pipe to route compressed air in and through the equipment without having to do a lot of complicated plumbing.

That approach would certainly work with all the obstructions in my shop. I chose a rubber hose rated for 250 pounds per square inch (psi), plenty for my little pancake compressor. The 1/2-in. inside diameter meant no reduction in air pressure would occur along the length of the run.

(Click Image to Expand)


(Click Image to Expand)

This story originally appeared in  American Woodworker September 2006, issue #123.

Source information may have changed since the original publication date.

Source  

MSC Industrial Supply, (800) 645-7270, www.mscdirect.com

September 2006, issue #123

Purchase this back issue.

Click here to read the rest of the article from American Woodworker