American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Power Sharpeners Santa Fe NM

If you haven't heard the word, there's been a quiet revolution in sharpening: abrasive discs. The idea is very simple. You take a round piece of PSA sandpaper, stick it onto a flat disc, and spin the disc with an electric motor. Hold a tool against the disc and suddenly you're removing metal at a pretty good clip– much faster than by hand.

Home Depot
(505) 424-9463
952 Richards Ave
Santa Fe, NM
 
Santa Fe Place
(505) 424-2600
4250 Cerrillos Rd
Santa Fe, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Kmart 3301 / Cross Merch
(505) 471-9007
1712 St Michaels Dr
Santa Fe, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Almuina Plasters
(505) 501-0786
2660 Ash St
Santa Fe, NM

Data Provided by:
Santa Fe By Design
(505) 988-4111
1512 Pacheco St Ste D101
Santa Fe, NM
 
The Home Depot
(505)424-9463
952 Richards Ave
Santa Fe, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Lowe's
(505) 819-4080
3458 Zafarano Road
Santa Fe, NM
Hours
M-SA 6 am - 9 pm
SU 8 am - 8 pm

Ace Hardware
(505) 424-9343
2006 Cerrillos Rd Ste 1
Santa Fe, NM
 
Lowe's Home Improvement Warehouse Of Sante Fe
(505) 819-4080
3458 Zafarano Dr
Santa Fe, NM
 
Baca J L Electric Co
(505) 983-6429
1508 1/2 Agua Fria St
Santa Fe, NM
 
Data Provided by:

Power Sharpeners

Power Sharpeners

3 sandpaper-based machines make sharpening easier than ever

If you haven't heard the word, there's been a quiet revolution in sharpening: abrasive discs. The idea is very simple. You take a round piece of PSA sandpaper, stick it onto a flat disc, and spin the disc with an electric motor. Hold a tool against the disc and suddenly you're removing metal at a pretty good clip– much faster than by hand. From set-up to keen edge, sharpening a dull tool usually takes less than 5 minutes. Coarse abrasive discs are a good substitute for a grinder–you can take out a nick or renew an old bevel very fast.  Fine abrasive discs can produce an edge equivalent to one made on a 4000 grit or higher waterstone, which is sharp enough for just about anybody. Three machines employ this technology: the Work Sharp WS3000 ($199), the Veritas Mk.II ($359), and the Lap-Sharp LS-200 ($595).  Each one is easy to set up and operate. If you've been confounded by all the details of using stones and a honing jig, these machines are a welcome relief. You'll be sharpening like a pro in just a few minutes. I tested these machines with a top-of-the-line Lie-Nielsen smoothing  plane, and found that each one is capable of producing a very fine edge, one that can make .002-in. thick shavings in the toughest woods, such as birdseye maple, quartersawn white oak and crotch walnut. The only downside to this method of sharpening is that the discs wear out. How much sandpaper will you need? Sharpening tasks vary so much that it's impossible to say, but each disc should see you through at least six sharpening sessions, and probably many more. Price and versatility vary widely among these machines. As detailed in the next pages, the more expensive the unit, the greater variety of tools it can sharpen. For more money, you also get a higher level of precision and a wider range of sharpening angles. Read on for a closer look at each model.

Work Sharp WS3000 $199


   

The Work Sharp WS3000 delivers the goods for the lowest price. It's a clever piece of engineering: on this machine, you can lap, grind, and hone most chisels, plane irons and carving tools. There is a width limit, however. The built-in tool rest (Photo 2) only accommodates blades up to 2 in. wide (the size of a No. 4 or No. 5 plane blade). It's possible to freehand grind and hone wider blades on top of the machine, but this requires skill and practice. The Work Sharp spins its 6-in. dia. discs at 580 rpm. That's much slower than a grinder, but you must still guard against overheating an edge.

PHOTO 1:
The Work Sharp's discs have sandpaper adhered to both sides. To prepare a blade for sharpening, flatten and smooth its back on the disc's top side.

  

PHOTO 2:
Sharpen the blade's bevel by sliding the tool up against the bottom of the disc. The tool rest til...

Click here to read the rest of the article from American Woodworker