American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Resawing Minot ND

Looking for Resawing in Minot? We have compiled a list of businesses and services around Minot that should help you with your search. We hope this page helps you find Resawing in Minot.

Dakota Sq Mall
(701) 857-1223
2400 10Th St Sw
Minot, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-20
Sun:12-18

Arrowhead Ace Hardware
(701) 839-6166
1600 2nd Ave SW
Minot, ND
 
Minot - D
(701) 852-4175
1 20Th Ave Se
Minot, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

ACME TOOLS- Minot
(701) 839-2263
700 20th Ave SE Minot, ND, 58701
Minot, ND
 
Mertz Construction & Supply
(701) 349-3209
45 West Main
Ellendale, ND
 
Fastenal- Minot
701-839-7566
700 20th Ave SW Minot, ND, 58701
Minot, ND
 
Muus Lumber & Hardware
(701) 852-4038
2700 Burdick Expressway E
Minot, ND
 
Enerbase
(701) 852-2501
215 Central Ave E
Minot, ND
 
The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Riverside Bldg Ctr Do it Best
(701) 683-4472
1015 S Main
Lisbon, ND
 

Recipe for Resawing - Techniques - American Woodworker

Recipe for Resawing

by Dave Munkittrick

For a woodworker, few things are more satisfying than resawing thin sheets of veneer off of a large block of wood or slicing a beautiful board in half to create two bookmatched pieces. I remember the enthusiasm I felt when I tried resawing for the first time. My excitement soon turned to disappointment however, as I watched my bandsaw chew up piece after piece of expensive walnut. Grrrrrr. It took me a long time to get over that initial experience. There’s no reason for you to share my pain, though. Here’s a recipe that will give you great results every time you resaw.

Choose the Right Blade

The single most important key to success is to use a sharp, high-quality blade. A dull blade is nothing but trouble. Here’s what to look for: First, use as wide a blade as your saw can handle. That said, we don’t recommend using a 3/4-in. blade on a 14-in. bandsaw unless the blade thickness is no more than .025. in. ( For more information, see “Premium Resaw Bandsaw Blades,” AW #91, December 2001, page 103. See page 5 for reprints. Also, see our resaw blade recommendations for 14-in. bandsaws in Sources, below.)

Second, choose a blade with three to four teeth per inch (tpi) and a 5- to 10-degree hook. Coarse blades have deeper gullets for better sawdust clearance. The hook tooth is an aggressive cutting design that lessens the feed pressure required. Reduced feed pressure keeps the blade from deflecting, which results in a straighter cut.


Adjust Tracking

With the saw unplugged, back off the thrust bearings and guides as far as possible. Mount the blade and temporarily set the tension according to the gauge on the saw. Manually spin the upper wheel and adjust the tracking knob until the blade is more or less centered on the wheel.


Set Blade Tension

The flutter test is the best way I’ve found to set the tension on a bandsaw blade. Keep the guides and bearings backed off and raise the blade guard to the maximum height. Stand clear of the blade and turn the machine on. Decrease the blade tension until the blade begins to flutter back and forth. Now, increase the tension until the blade flutter is eliminated. Add a one-half turn or so to the tension knob and the blade tension should be just right. 


Adjust the Guides

I use the thickness of a dollar bill or a piece of paper as a spacer for setting the guide blocks and thrust bearings. First, set the blade guide arm so it’s about 1/4 in. above the height of the stock you’re resawing. Then bring the guide block assembly forward until the fronts of the blocks are even with the bottoms of the blade gullets. Wrap a dollar bill around the blade and set the blocks up tight against the sides of the blade. Use the bill again to set the thrust bearing behind the blade. Repeat the process for the lower guide blocks and thrust bearin...

Click here to read the rest of the article from American Woodworker