American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Rollers Ease Plywood Storage Claremore OK

Plywood storage roller works great and it's simple to make. The following article has some tips to offer to help you build your own storage roller. So read on to get more details below.

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Claremore - Auth Hometown
(918) 343-2500
1648 North Lynn Riggs Blvd
Claremore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20

Westlake Ace Hardware
(918) 343-3117
810 N Lynn Riggs Blvd
Claremore, OK
 
Cribbets True Value
(918) 371-3306
1008 Main St
Collinsville, OK
 
LOWE'S OF OWASSO, OK
918 274-0881
12001 E. 96TH STREET NORTH OWASSO, OK, 74055
Owasso, OK
 
Fastenal- Claremore
918-342-4548
1614 North Lynn Riggs Blvd Claremore, OK, 74017
Claremore, OK
 
Pixley Lumber Co
(918) 341-4223
715 W Will Rogers
Claremore, OK
 
Lowe's
(918) 923-1030
1746 South Lynn Riggs Boulevard
Claremore, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Lowe's
(918) 274-0881
12001 E. 96Th Street North
Owasso, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Pryor Lumber
(918) 825-2260
1031 West Highway 20
Pryor, OK
 

Rollers Ease Plywood Storage

Rollers Ease Plywood Storage

Before I installed these rollers, sliding plywood in and out of my storage rack used to wear me out. It also damaged the edges of the sheets. Now plywood sheets glide in and out.I cut the 2-1/2-in.-dia. rollers from 3/4-in. hard maple on my drill press using a fly cutter. You could also cut them on a bandsaw with a circle-cutting jig. I drilled out the centers to 17/32 in., so they would spin on the 1/2-in. hex-head bolts I use as spindles.My rack consists of four evenly spaced blocks attached to uprights and a 4-in.-wide x 6-ft.-long solid-wood backboard. The backboard is screwed tothe wall; the uprights fasten to a board mounted on the ceiling.

Before assembling the rack, I laid out and drilled holes in the uprights and backboard for the hex-head bolts. I counterbored the backboard’s holes for the 1/2-in. nuts that the 7-in.-long bolts screw into. After screwing the blocks to the backboard and installing the nuts, I screwed the assembly to the wall. Then I screwed each upright to the block on the floor and the board on the ceiling. Installing the rollers and their 1/2-in. washer spacers was the last step. I slid them onto the bolts before screwing the bolts into the backboard’s housed nuts.

Click here to read the rest of the article from American Woodworker