American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Rollers Ease Plywood Storage Osseo MN

Plywood storage roller works great and it's simple to make. The following article has some tips to offer to help you build your own storage roller. So read on to get more details below.

The Home Depot
(763)494-0117
15800 Grove Circle North
Maple Grove, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)422-1200
3550 124th Ave NW
Coon Rapids, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)571-9600
5650 Main St, NE
Fridley, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #14
(952) 542-0111
12995 Ridgedale Dr.
Minnetonka, MN

Data Provided by:
The Home Depot
(763)717-0316
4550 Pheasant Ridge Dr
Blaine, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)533-1200
6701 Boone Ave North
Brooklyn Park, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)509-9590
1705 Annapolis Lane
Plymouth, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)795-2060
99 Northtown Drive
Blaine, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(612)782-9594
1520 New Brighton Blvd
Minneapolis, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(952)512-0109
5800 Cedar Lake Rd
St Louis Park, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Rollers Ease Plywood Storage

Rollers Ease Plywood Storage

Before I installed these rollers, sliding plywood in and out of my storage rack used to wear me out. It also damaged the edges of the sheets. Now plywood sheets glide in and out.I cut the 2-1/2-in.-dia. rollers from 3/4-in. hard maple on my drill press using a fly cutter. You could also cut them on a bandsaw with a circle-cutting jig. I drilled out the centers to 17/32 in., so they would spin on the 1/2-in. hex-head bolts I use as spindles.My rack consists of four evenly spaced blocks attached to uprights and a 4-in.-wide x 6-ft.-long solid-wood backboard. The backboard is screwed tothe wall; the uprights fasten to a board mounted on the ceiling.

Before assembling the rack, I laid out and drilled holes in the uprights and backboard for the hex-head bolts. I counterbored the backboard’s holes for the 1/2-in. nuts that the 7-in.-long bolts screw into. After screwing the blocks to the backboard and installing the nuts, I screwed the assembly to the wall. Then I screwed each upright to the block on the floor and the board on the ceiling. Installing the rollers and their 1/2-in. washer spacers was the last step. I slid them onto the bolts before screwing the bolts into the backboard’s housed nuts.

Click here to read the rest of the article from American Woodworker