American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Rollers Ease Plywood Storage Richmond KY

Plywood storage roller works great and it's simple to make. The following article has some tips to offer to help you build your own storage roller. So read on to get more details below.

Woodcraft - Lexington, KY
(859) 231-9663
3028 Blake James Drive
Lexington, KY

Data Provided by:
Fastenal- Richmond
859-624-2136
6013 Atwood Drive Richmond, KY, 40475
Richmond, KY
 
Ace Hardware
(859) 623-2380
670 University Shopping Ctr
Richmond, KY
 
Richmond - Auth Hometown
(859) 623-2670
830 Eastern Bypass
Richmond, KY
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-19
Sun:12.5-17.5
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-19
Sun:12.5-17.5

Jennings Do it Best Home Cente
(859) 986-0355
1187 Paint Lick Road
Berea, KY
 
The Home Depot
(859)269-4774
2397 Richmond Rd
Lexington, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(859) 625-0251
814 Eastern Bypass
Richmond, KY
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

LOWE'S OF RICHMOND, KY.
859 625-0251
814 EASTERN BYPASS RICHMOND, KY, 40475
Richmond, KY
 
Ace Hardware-Berea
(859) 985-0747
292 Mini Mall Dr, Boone Square Shopping Center
Berea, KY
 
Lowe's
(859) 881-6200
1421 Keene Road
Nicholasville, KY
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Data Provided by:

Rollers Ease Plywood Storage

Rollers Ease Plywood Storage

Before I installed these rollers, sliding plywood in and out of my storage rack used to wear me out. It also damaged the edges of the sheets. Now plywood sheets glide in and out.I cut the 2-1/2-in.-dia. rollers from 3/4-in. hard maple on my drill press using a fly cutter. You could also cut them on a bandsaw with a circle-cutting jig. I drilled out the centers to 17/32 in., so they would spin on the 1/2-in. hex-head bolts I use as spindles.My rack consists of four evenly spaced blocks attached to uprights and a 4-in.-wide x 6-ft.-long solid-wood backboard. The backboard is screwed tothe wall; the uprights fasten to a board mounted on the ceiling.

Before assembling the rack, I laid out and drilled holes in the uprights and backboard for the hex-head bolts. I counterbored the backboard’s holes for the 1/2-in. nuts that the 7-in.-long bolts screw into. After screwing the blocks to the backboard and installing the nuts, I screwed the assembly to the wall. Then I screwed each upright to the block on the floor and the board on the ceiling. Installing the rollers and their 1/2-in. washer spacers was the last step. I slid them onto the bolts before screwing the bolts into the backboard’s housed nuts.

Click here to read the rest of the article from American Woodworker