American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Router-Made Drawer and Door Pulls Bristol RI

You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

St. Angelo Hardwoods, Inc. - Genuine Asian Teak Specialist
(401) 624-3900
490 Eagleville Road
Tiverton, RI

Data Provided by:
The Home Depot
(401)845-5092
878 W Main Road
Middletown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(401)295-1184
1255 Ten Rod Road
North Kingstown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Handren's Paint & Hardware
(401) 293-5290
3001 East Main Road
Portsmouth, RI
 
Rhode Island Mall
(401) 827-4800
650 Bald Hill Rd
Warwick, RI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5

Good Wood
(508) 344-7888
1025 Drift Rd
Westport, MA

Data Provided by:
Woodcraft - Providence, RI
(401) 886-1175
1000 Division Street
East Greenwich, RI

Data Provided by:
The Home Depot
(401)823-5173
700 Centre Of N E Blvd
Coventry, RI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Lowe's
(401) 822-6300
510 Quaker Lane
Warwick, RI
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Standard Do it Best Hardware
(401) 438-1420
360 Taunton Ave
East Providence, RI
 
Data Provided by:

Router-Made Drawer and Door Pulls

Router-Made Drawer and Door Pulls



You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

Finger-Pull Door Lip



These doors have a roundover on the back and a decorative cove on the front. The roundover on the back creates just enough room for your fingers to catch hold of the door. This decorative edge treatment around the entire door complements a frame-and-panel style quite nicely. Use European-style hinges and you'll have no visible hardware.

The Bit


Specifically designed for creating pulls, this router bit has no bearing and is quite large with a diameter of 1-3/4 in. Use the bit in a router table and take three or four passes. The door shown is 3/4-in. thick, but this bit will work on doors as thick as 1-1/4 in. Be sure to test the bit on scrap pieces of wood of the same species you're working with and to experiment with different speeds. Some species will chip or splinter at one speed but may work well at a different speed.

Source: Freud Tools, (800) 472-7307, www.freudtools.com
Finger-pull door-lip bit, #FRD 99-065, $49.

Hidden Cove



This hidden pull is made by an ordinary cove bit. It works well on solid wood, fibercore or plywood. On fibercore and plywood, first add a 1/8-in. to 1/4-in. solid-wood edge to the panel's edges and then rout the cove. Some core will be exposed after routing, but it will be hidden after the door is installed.

The Bit


For this cabinet, I used a 1/2-in. cove bit with a bottom bearing. This bit works equally well in a handheld router or a router table. Leave about a 1/4-in. flat lip on the front of the panel.

Source: Oldham, (888) 678-7278, 1/2-in. cove bit, #3164COV, $34.

Dovetail Bevel



This visible decorative pull is made using an ordinary dovetail bit. The entire length of the door's inner edge can be used as a pull. I used a shop-made template as a guide to create a circular design in the middle to complement the cabinet's modern look.

The Setup
Use a router with a guide bushing to follow the template. The template can be made in whatever shape you choose.

I chose a circle to add some interest to the simple shape of the cabinet. I used a handheld router so I could easily see when the semicircle was completely cut out. When you're done routing, soften the edges slightly with sandpaper.

The Bit


This 3/4-in.-dia. dovetail bit has a 14-degree angle that leaves an easy-to-grip edge. On these 3/4-in.-thick doors, I set the bit to cut 1/2 in. deep. Any deeper than this would weaken the door's revealed back edge.

Source: Freud Tools, (800) 472-7307, www.freudtools.com 3/4-in.-dia. dovetail bit, #FRD 22-134, $20.

Finger Grip



This visible decorative pull is made by a specialty bit. The shape is routed into an applied solid-wood edging. Use...

Click here to read the rest of the article from American Woodworker