American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Router-Made Drawer and Door Pulls Keene NH

You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

Jacks True Value Hardware
(603) 352-1517
37 Park Ave.
Keene, NH
 
W W Building Supply
(802) 365-4333
7 Loop Rd
Newfane, VT
 
The Home Depot
(603)542-4471
425 Washington St
Claremont, NH
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Northland Forest Products, Inc.
(603) 642-3665
16 Church StreetPO Box 369
Kingston, NH

Data Provided by:
Woodcraft - Portsmouth, NH
(603) 433-6116
25 Fox Run Road
Newington, NH

Data Provided by:
Keene - B
(603) 338-5000
480 West St
Keene, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19

Best Septic
(802) 463-9444
153 Birchview Ext
Westminster, VT
Services Offered
Waste services, porta potty, jetting, portable toilet rentals, septic solutions, locating septic tanks, septic tank repair, septic tank cleaning, septic tank filters, septic tank services, snaking, camera service, septic trouble shooting, hand wash station rentals, septic design, septic installation, septic maintenance
Hours
24/7 Emergency Service

Rockler Woodworking and Hardware #34
(603) 898-5941
373 S. Broadway
Salem, NH

Data Provided by:
Goosebay Sawmill & Lumber
(603) 798-5135
83 Dover Road Route 4
Chichester, NH

Data Provided by:
Warren's Hardware
(603) 664-9300
585 Calef Hwy, Unit 3
Barrington, NH
 
Data Provided by:

Router-Made Drawer and Door Pulls

Router-Made Drawer and Door Pulls



You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

Finger-Pull Door Lip



These doors have a roundover on the back and a decorative cove on the front. The roundover on the back creates just enough room for your fingers to catch hold of the door. This decorative edge treatment around the entire door complements a frame-and-panel style quite nicely. Use European-style hinges and you'll have no visible hardware.

The Bit


Specifically designed for creating pulls, this router bit has no bearing and is quite large with a diameter of 1-3/4 in. Use the bit in a router table and take three or four passes. The door shown is 3/4-in. thick, but this bit will work on doors as thick as 1-1/4 in. Be sure to test the bit on scrap pieces of wood of the same species you're working with and to experiment with different speeds. Some species will chip or splinter at one speed but may work well at a different speed.

Source: Freud Tools, (800) 472-7307, www.freudtools.com
Finger-pull door-lip bit, #FRD 99-065, $49.

Hidden Cove



This hidden pull is made by an ordinary cove bit. It works well on solid wood, fibercore or plywood. On fibercore and plywood, first add a 1/8-in. to 1/4-in. solid-wood edge to the panel's edges and then rout the cove. Some core will be exposed after routing, but it will be hidden after the door is installed.

The Bit


For this cabinet, I used a 1/2-in. cove bit with a bottom bearing. This bit works equally well in a handheld router or a router table. Leave about a 1/4-in. flat lip on the front of the panel.

Source: Oldham, (888) 678-7278, 1/2-in. cove bit, #3164COV, $34.

Dovetail Bevel



This visible decorative pull is made using an ordinary dovetail bit. The entire length of the door's inner edge can be used as a pull. I used a shop-made template as a guide to create a circular design in the middle to complement the cabinet's modern look.

The Setup
Use a router with a guide bushing to follow the template. The template can be made in whatever shape you choose.

I chose a circle to add some interest to the simple shape of the cabinet. I used a handheld router so I could easily see when the semicircle was completely cut out. When you're done routing, soften the edges slightly with sandpaper.

The Bit


This 3/4-in.-dia. dovetail bit has a 14-degree angle that leaves an easy-to-grip edge. On these 3/4-in.-thick doors, I set the bit to cut 1/2 in. deep. Any deeper than this would weaken the door's revealed back edge.

Source: Freud Tools, (800) 472-7307, www.freudtools.com 3/4-in.-dia. dovetail bit, #FRD 22-134, $20.

Finger Grip



This visible decorative pull is made by a specialty bit. The shape is routed into an applied solid-wood edging. Use...

Click here to read the rest of the article from American Woodworker