American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Router-Made Drawer and Door Pulls Mansfield TX

You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

The Home Depot
(817)453-4038
1725 N US Hwy 287
Mansfield, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #27
(817) 417-0070
4624 South Cooper St.
Arlington, TX

Data Provided by:
The Home Depot
(972)602-9385
5280 South Hwy 360
Grand Prairie, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)293-0343
7950 I-35 W South Fwy
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)496-3212
1151 Bridgewood Dr
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)468-4224
4611 S Cooper St
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)447-6602
300 NW John Jones
Burleson, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(972)299-9390
373 E Fm 1382
Cedar Hill, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)459-4300
201 Rd To Six Flags West
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Brazos Forest Products - Grand Prairie
(972) 602-1225
2760 N Great SW Parkway
Grand Prairie, TX

Data Provided by:
Data Provided by:

Router-Made Drawer and Door Pulls

Router-Made Drawer and Door Pulls



You can make integrated pulls yourself using a router table and a few bits. They can be decorative or almost completely hidden. Of the four designs I'll describe for you, two require special bits, but two use ordinary bits that you may already own.

Finger-Pull Door Lip



These doors have a roundover on the back and a decorative cove on the front. The roundover on the back creates just enough room for your fingers to catch hold of the door. This decorative edge treatment around the entire door complements a frame-and-panel style quite nicely. Use European-style hinges and you'll have no visible hardware.

The Bit


Specifically designed for creating pulls, this router bit has no bearing and is quite large with a diameter of 1-3/4 in. Use the bit in a router table and take three or four passes. The door shown is 3/4-in. thick, but this bit will work on doors as thick as 1-1/4 in. Be sure to test the bit on scrap pieces of wood of the same species you're working with and to experiment with different speeds. Some species will chip or splinter at one speed but may work well at a different speed.

Source: Freud Tools, (800) 472-7307, www.freudtools.com
Finger-pull door-lip bit, #FRD 99-065, $49.

Hidden Cove



This hidden pull is made by an ordinary cove bit. It works well on solid wood, fibercore or plywood. On fibercore and plywood, first add a 1/8-in. to 1/4-in. solid-wood edge to the panel's edges and then rout the cove. Some core will be exposed after routing, but it will be hidden after the door is installed.

The Bit


For this cabinet, I used a 1/2-in. cove bit with a bottom bearing. This bit works equally well in a handheld router or a router table. Leave about a 1/4-in. flat lip on the front of the panel.

Source: Oldham, (888) 678-7278, 1/2-in. cove bit, #3164COV, $34.

Dovetail Bevel



This visible decorative pull is made using an ordinary dovetail bit. The entire length of the door's inner edge can be used as a pull. I used a shop-made template as a guide to create a circular design in the middle to complement the cabinet's modern look.

The Setup
Use a router with a guide bushing to follow the template. The template can be made in whatever shape you choose.

I chose a circle to add some interest to the simple shape of the cabinet. I used a handheld router so I could easily see when the semicircle was completely cut out. When you're done routing, soften the edges slightly with sandpaper.

The Bit


This 3/4-in.-dia. dovetail bit has a 14-degree angle that leaves an easy-to-grip edge. On these 3/4-in.-thick doors, I set the bit to cut 1/2 in. deep. Any deeper than this would weaken the door's revealed back edge.

Source: Freud Tools, (800) 472-7307, www.freudtools.com 3/4-in.-dia. dovetail bit, #FRD 22-134, $20.

Finger Grip



This visible decorative pull is made by a specialty bit. The shape is routed into an applied solid-wood edging. Use...

Click here to read the rest of the article from American Woodworker