American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Router Wrench Risers Albuquerque NM

Fasten a gasket on each side of one wrench with spray adhesive or contact cement. Then use a utility knife to sculpt the opening. The following article has more tips.

The Home Depot
(505)344-1900
1220 Renaissance Blvd NE
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(505)833-9990
2820 Coors Blvd NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(505)899-1290
10200 Coors Dr NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Kmart 4136 / Cross Merch
(505) 265-5911
2100 Carlisle Ave Ne
Albuquerque, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Ace Hardware
(505) 266-4000
1100 San Mateo Blvd NE, NE corner of San Mateo & Lomas
Albuquerque, NM
 
Woodcraft - Albuquerque, NM
(505) 342-9663
4520B Alexander NE
Albuquerque, NM

Data Provided by:
The Home Depot
(505)271-1900
200 Eubank Blvd SE
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(505)771-3523
7700 US 550 NE
Rio Rancho, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Coronado Ctr
(505) 881-5570
6600 Menaul Blvd Ne Ste 700
Albuquerque, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-19
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-19
Store Features
Mon:10-21
Tue:10-19
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-19

Fastenal- Albuquerque
505-880-1124
2923 Girard Blvd NE Albuquerque, NM, 87107
Albuquerque, NM
 
Data Provided by:

Router Wrench Risers

Router Wrench Risers

Trying to keep the wrenches that came with my router in position for tightening or loosening the collet used to drive me crazy. The nuts are so widely spaced that the slim wrenches would often slip out of place. 

Fortunately, I discovered a solution at my local hardware store: basin mack gaskets, which are stepped rubber washers used while installing sinks. 

Fasten a gasket on each side of one wrench with spray adhesive or contact cement. Then use a utility knife to sculpt the opening. 

During use, the gasket-covered wrench goes on the shaft nut. One gasket holds this wrench away from the motor housing. The other gasket acts as a platform for the wrench that goes on the collet nut. If the gaskets are too thick to properly align the wrenches, just slice them thinner. One side of this wrench works for tightening; flip it over for loosening. 

Click here to read the rest of the article from American Woodworker