American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Shop-Made Router Lift Rutherfordton NC

This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Packard Woodworks (Tools Only - No Wood)
(800) 683-8876
PO Box 718
Tryon, NC

Data Provided by:
Forest City Ace Hardware
(828) 245-4412
171 E Main St
Forest City, NC
 
Fastenal- Forest City
828-287-2166
525 Withrow Rd Forest City, NC, 28043
Forest City, NC
 
Landrum Do it Best Hardware
(864) 457-2324
216 East Rutherford St
Landrum, SC
 
Woodcraft - Raleigh/Durham, NC
(919) 781-1911
4317 Pleasant Valley Road
Raleigh, NC

Data Provided by:
Hill Hardware, Inc.
(828) 287-4105
184 North Main St
Rutherfordton, NC
 
LOWE'S OF FOREST CITY, NC
828 351-1023
184 LOWE'S BOULEVARD FOREST CITY, NC, 28043
Forest City, NC
 
Lowe's
(828) 351-1023
184 Lowe'S Boulevard
Forest City, NC
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Hill's Hardware
(828) 287-4105
184 N Main St
Rutherfordton, NC

Data Provided by:
The Home Depot
(828)667-9298
127 Acton Cr
Asheville, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Shop-Made Router Lift

Shop-Made Router Lift



Router lifts are hot items these days and for good reason. Veteranrouter table users love their ability to make super-fine microadjustments or rapidly raise the bit right from the tabletop. No morefumbling under the table like a contortionist. The only drawback is theprice: $200 to $500. Ouch! That's why we were so thrilled when RichardTendick walked into our offices with his idea for a shop-made routerlift. Not only does Richard's lift offer above-the-table heightadjustment (see “Benefits of the AW Router Lift,”) but it costs lessthan $100. Plus, unlike the expensive commercial lifts, this liftallows you to change bits without cranking the router all the way up.It also features effective below-the-table dust collection. Whencombined with dust collection in the fence it results in near-perfectdust collection. This design also isolates the exhaust end of therouter in the cavity. That leaves the router air intake sucking onlyclean, dust-free air. And, unlike all the other mechanical lifts on themarket, Richard's lift hangs off the back of the router table, not onthe top where the excess weight can lead to sagging.



Our router lift consists of two components: the lift mechanism and therouter carrier. The lift mechanism uses finely machined steel rods thatslide through oil-impregnated bronze bushings set in upper and lowerslide blocks. Upper and lower clamp blocks capture the ends of thesteel rods and provide attachment points for securing the lift to therouter table back. The router carrier attaches to the lift mechanism. Aplywood router clamp holds the router motor in the carrier. Adjustingthe height is as simple as turning the acorn nut on top of a threadedrod.

Benefits of the AW Router Lift



Bit height changes are quick and precise. A speed wrench allows you toraise the router bit to any height in seconds. For fine adjustments, aone-quarter turn of the wrench equals a mere 1/64-in. change in bitheight.



Changing router bits is fast and easy. The lift is mounted to thecabinet, not the top. This allows you to hinge the top for easy accessto the router. It makes bit changes a snap.



Router table dust collection that really works! Two side boards mountedalongside the lift create a cavity like an elevator shaft. Wood dust iscaptured in the cavity and vented out a dust port in the router carrier.

Will It Fit My Router Table?
If you already own a full-size router table don't sweat. A few simplemodifications allow you to mount the AW lift into most commercialtables (see “Fitting the AW Lift to Your Router,”).

What You'll Need
This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Click here to read the rest of the article from American Woodworker