American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Shop-Made Router Lift Springfield VA

This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Woodcraft - Springfield
(703) 912-6727
Concord Shopping Center
Springfield, VA

Data Provided by:
The Home Depot
(703)642-3660
6555 Little River Trnpke
Alexandria, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)823-1900
400 S Pickett St
Alexandria, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)619-5124
7710 Richmond Hwy
Alexandria, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Vienna Hardwoods
(703) 255-9663
241 Mill Street Northeast
Vienna, VA

Data Provided by:
The Home Depot
(703)924-0193
6691 Frontier Road
Springfield, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)205-1245
2815 Merrilee Drive
Fairfax, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)534-9580
6210 Seven Corners Ctr
Falls Church, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)591-6808
3201 Old Lee Highway
Fairfax, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)670-3699
14025 Foulger Square
Woodbridge, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Shop-Made Router Lift

Shop-Made Router Lift



Router lifts are hot items these days and for good reason. Veteranrouter table users love their ability to make super-fine microadjustments or rapidly raise the bit right from the tabletop. No morefumbling under the table like a contortionist. The only drawback is theprice: $200 to $500. Ouch! That's why we were so thrilled when RichardTendick walked into our offices with his idea for a shop-made routerlift. Not only does Richard's lift offer above-the-table heightadjustment (see “Benefits of the AW Router Lift,”) but it costs lessthan $100. Plus, unlike the expensive commercial lifts, this liftallows you to change bits without cranking the router all the way up.It also features effective below-the-table dust collection. Whencombined with dust collection in the fence it results in near-perfectdust collection. This design also isolates the exhaust end of therouter in the cavity. That leaves the router air intake sucking onlyclean, dust-free air. And, unlike all the other mechanical lifts on themarket, Richard's lift hangs off the back of the router table, not onthe top where the excess weight can lead to sagging.



Our router lift consists of two components: the lift mechanism and therouter carrier. The lift mechanism uses finely machined steel rods thatslide through oil-impregnated bronze bushings set in upper and lowerslide blocks. Upper and lower clamp blocks capture the ends of thesteel rods and provide attachment points for securing the lift to therouter table back. The router carrier attaches to the lift mechanism. Aplywood router clamp holds the router motor in the carrier. Adjustingthe height is as simple as turning the acorn nut on top of a threadedrod.

Benefits of the AW Router Lift



Bit height changes are quick and precise. A speed wrench allows you toraise the router bit to any height in seconds. For fine adjustments, aone-quarter turn of the wrench equals a mere 1/64-in. change in bitheight.



Changing router bits is fast and easy. The lift is mounted to thecabinet, not the top. This allows you to hinge the top for easy accessto the router. It makes bit changes a snap.



Router table dust collection that really works! Two side boards mountedalongside the lift create a cavity like an elevator shaft. Wood dust iscaptured in the cavity and vented out a dust port in the router carrier.

Will It Fit My Router Table?
If you already own a full-size router table don't sweat. A few simplemodifications allow you to mount the AW lift into most commercialtables (see “Fitting the AW Lift to Your Router,”).

What You'll Need
This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Click here to read the rest of the article from American Woodworker