American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Shop-Made Router Lift Woodinville WA

This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Hardwoods Supply, Inc.
(425) 883-4733
14515 NE 91st Street
Redmond, WA

Data Provided by:
Home Depot Inc
(425) 806-9300
18333 120th Ave Ne
Bothell, WA
 
The Home Depot
(425)451-7351
325 120th Ave NE
Bellevue, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(425)267-0337
11915 Highway 99
Everett, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(360)568-8687
2601 Bickford Avenue
Snohomish, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(425)885-6358
17777 NE 76th Street
Redmond, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(425)806-9300
18333 120th Ave NE
Bothell, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(206)361-9600
11616 Aurora Ave N
Seattle, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Rockler Woodworking and Hardware #2
(206) 634-3222
3823 Stone Way North
Seattle, WA

Data Provided by:
Home Depot
(425) 391-8467
6200 E Lake Sammamish Pkwy Se
Redmond, WA
 
Data Provided by:

Shop-Made Router Lift

Shop-Made Router Lift



Router lifts are hot items these days and for good reason. Veteranrouter table users love their ability to make super-fine microadjustments or rapidly raise the bit right from the tabletop. No morefumbling under the table like a contortionist. The only drawback is theprice: $200 to $500. Ouch! That's why we were so thrilled when RichardTendick walked into our offices with his idea for a shop-made routerlift. Not only does Richard's lift offer above-the-table heightadjustment (see “Benefits of the AW Router Lift,”) but it costs lessthan $100. Plus, unlike the expensive commercial lifts, this liftallows you to change bits without cranking the router all the way up.It also features effective below-the-table dust collection. Whencombined with dust collection in the fence it results in near-perfectdust collection. This design also isolates the exhaust end of therouter in the cavity. That leaves the router air intake sucking onlyclean, dust-free air. And, unlike all the other mechanical lifts on themarket, Richard's lift hangs off the back of the router table, not onthe top where the excess weight can lead to sagging.



Our router lift consists of two components: the lift mechanism and therouter carrier. The lift mechanism uses finely machined steel rods thatslide through oil-impregnated bronze bushings set in upper and lowerslide blocks. Upper and lower clamp blocks capture the ends of thesteel rods and provide attachment points for securing the lift to therouter table back. The router carrier attaches to the lift mechanism. Aplywood router clamp holds the router motor in the carrier. Adjustingthe height is as simple as turning the acorn nut on top of a threadedrod.

Benefits of the AW Router Lift



Bit height changes are quick and precise. A speed wrench allows you toraise the router bit to any height in seconds. For fine adjustments, aone-quarter turn of the wrench equals a mere 1/64-in. change in bitheight.



Changing router bits is fast and easy. The lift is mounted to thecabinet, not the top. This allows you to hinge the top for easy accessto the router. It makes bit changes a snap.



Router table dust collection that really works! Two side boards mountedalongside the lift create a cavity like an elevator shaft. Wood dust iscaptured in the cavity and vented out a dust port in the router carrier.

Will It Fit My Router Table?
If you already own a full-size router table don't sweat. A few simplemodifications allow you to mount the AW lift into most commercialtables (see “Fitting the AW Lift to Your Router,”).

What You'll Need
This project requires some specialized hardware unfamiliar to mostwoodworkers, like bronze bearings and steel rod. We recommend you buyyour lifter parts from the mail order sources we used (see Sourcesbelow).

Click here to read the rest of the article from American Woodworker