American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sharpening Jig Beatrice NE

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. Here you will learn how to make your own shop made jigs for woodworking. You also get the option of choosing to buy one of the many different sharpening jig power tools at the hardware supply stores in Beatrice, NE listed below.

Mead Lumber
(402) 223-5264
700 Dorsey St
Beatrice, NE
 
Beatrice - Auth Hometown
(402) 223-3827
1200 N 6Th St Ste C
Beatrice, NE
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18.5
Tue:9-18.5
Wed:9-18.5
Thu:9-18.5
Fri:9-18.5
Sat:9-18
Sun:11-16
Store Features
Mon:9-18.5
Tue:9-18.5
Wed:9-18.5
Thu:9-18.5
Fri:9-18.5
Sat:9-18
Sun:11-16

Fastenal- Beatrice
402-228-1600
3414 N 6th Street Beatrice, NE, 68310
Beatrice, NE
 
The Home Depot
(308)630-2398
3102 Avenue I
Scottsbluff, NE
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(402)333-9477
12710 L Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Watkins Ace Hardware
(402) 223-2400
2317 N 6th St
Beatrice, NE
 
Sack Do it Best Lumber
(402) 223-3545
2820 East Court
Beatrice, NE
 
Sack Lumber Company
(402) 821-2812
316 S Wilson Street
Wilber, NE
 
The Home Depot
(402)573-6393
4545 North 72nd Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(402)331-2879
712 N Washington St
Papillion, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-7:00pm

Sharpening Jig

Simple Sharpening Jig

I’ve tried several different shop-made jigs for sharpening my jointer and planer knives but this one has proved the simplest to use and make. 

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. My jointer blades required a 38-degree angle but check yours because it may be different. 

I also had to saw the angled slots with the board on its edge. That’s because my tablesaw (like most) tilts to only 45 degrees. This is not far enough for the slot to be cut with the board laying flat. Cutting it on its edge solves this problem. Take a look at your saw and you will see what I mean. Double-check the angle of your jointer knives and saw the slots to match. I added a blade guard to keep things safe.

For the sanding block I used chunks of 3/4-in. MDF with sheets of silicon carbide sandpaper attached with spray-on adhesive. I started with 220 grit and worked my way up to 600 grit for a final honing. 


Click here to read the rest of the article from American Woodworker