American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sharpening Jig Gallup NM

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. Here you will learn how to make your own shop made jigs for woodworking. You also get the option of choosing to buy one of the many different sharpening jig power tools at the hardware supply stores in Gallup, NM listed below.

The Home Depot
(505)726-2362
530 Kachina Street
Gallup, NM
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

Gallup - Auth Hometown
(505) 863-9336
901 Metro Ave
Gallup, NM
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-18.5
Tue:9.5-18.5
Wed:9.5-18.5
Thu:9.5-18.5
Fri:9.5-18.5
Sat:9-18
Sun:12-17
Store Features
Mon:9.5-18.5
Tue:9.5-18.5
Wed:9.5-18.5
Thu:9.5-18.5
Fri:9.5-18.5
Sat:9-18
Sun:12-17

The Home Depot
(575)521-1327
225 Telshore Blvd
Las Cruces, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(505)899-1290
10200 Coors Dr NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(505)344-1900
1220 Renaissance Blvd NE
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Gallup Lumber & Ace Hardware
(505) 863-4475
1724 S 2nd St, Corner of Second Street & Nizhoni
Gallup, NM
 
The Home Depot
(505)771-3523
7700 US 550 NE
Rio Rancho, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(575)443-8018
3400 N White Sand Blvd
Alamogordo, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(575)492-9117
900 W Joe Harvey Blvd
Hobbs, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(505)726-2362
530 Kachina Street
Gallup, NM
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

Sharpening Jig

Simple Sharpening Jig

I’ve tried several different shop-made jigs for sharpening my jointer and planer knives but this one has proved the simplest to use and make. 

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. My jointer blades required a 38-degree angle but check yours because it may be different. 

I also had to saw the angled slots with the board on its edge. That’s because my tablesaw (like most) tilts to only 45 degrees. This is not far enough for the slot to be cut with the board laying flat. Cutting it on its edge solves this problem. Take a look at your saw and you will see what I mean. Double-check the angle of your jointer knives and saw the slots to match. I added a blade guard to keep things safe.

For the sanding block I used chunks of 3/4-in. MDF with sheets of silicon carbide sandpaper attached with spray-on adhesive. I started with 220 grit and worked my way up to 600 grit for a final honing. 


Click here to read the rest of the article from American Woodworker