American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sharpening Jig Nashville TN

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. Here you will learn how to make your own shop made jigs for woodworking. You also get the option of choosing to buy one of the many different sharpening jig power tools at the hardware supply stores in Nashville, TN listed below.

The Home Depot
(615)269-7800
2535 Powell Ave
Nashville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)865-9600
1584 Gallatin Pike N
Madison, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)370-0730
8101 Moores Lane
Brentwood, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)662-7600
7665 Highway 70 South
Nashville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)599-4578
224 S Royal Oaks Blvd
Franklin, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)228-3317
1015 Joyce Lane
Nashville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)731-2900
1155 Bell Rd
Antioch, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)889-7211
5010 Old Hickory Blvd
Hermitage, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)824-2391
205 N Anderson Lane
Hendersonville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Nashville, TN
(615) 599-9638
209 S. Royal Oaks Blvd.
Franklin, TN

Data Provided by:
Data Provided by:

Sharpening Jig

Simple Sharpening Jig

I’ve tried several different shop-made jigs for sharpening my jointer and planer knives but this one has proved the simplest to use and make. 

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. My jointer blades required a 38-degree angle but check yours because it may be different. 

I also had to saw the angled slots with the board on its edge. That’s because my tablesaw (like most) tilts to only 45 degrees. This is not far enough for the slot to be cut with the board laying flat. Cutting it on its edge solves this problem. Take a look at your saw and you will see what I mean. Double-check the angle of your jointer knives and saw the slots to match. I added a blade guard to keep things safe.

For the sanding block I used chunks of 3/4-in. MDF with sheets of silicon carbide sandpaper attached with spray-on adhesive. I started with 220 grit and worked my way up to 600 grit for a final honing. 


Click here to read the rest of the article from American Woodworker