American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sharpening Jig Tahlequah OK

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. Here you will learn how to make your own shop made jigs for woodworking. You also get the option of choosing to buy one of the many different sharpening jig power tools at the hardware supply stores in Tahlequah, OK listed below.

1404 S Muskogee Ave
(918) 431-1717
Ste #7
Tahlequah, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:13-18
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:13-18

Lowe's
(918) 708-4000
161 Meadow Creek Drive
Tahlequah, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Masters True Value Hardware
(918) 456-4122
128 N Muskogee Ave
Tahlequah, OK
 
Masters True Value Hardware
(800) 642-7392
128 N Muskogee Ave
Tahlequah, OK

Data Provided by:
The Home Depot
(918)459-3700
9808 East 71st
Tulsa, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Tahlequah Lumber
(918) 456-2506
1701 Park Hill Road
Tahlequah, OK
 
LOWE'S OF TAHLEQUAH, OK
918 708-4000
161 MEADOW CREEK DRIVE TAHLEQUAH, OK, 74464
Tahlequah, OK
 
Keith True Value
(918) 478-2327
911 S Lee
Fort Gibson, OK
 
The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(405)579-7700
850 Ed Noble Pkwy
Norman, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Sharpening Jig

Simple Sharpening Jig

I’ve tried several different shop-made jigs for sharpening my jointer and planer knives but this one has proved the simplest to use and make. 

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. My jointer blades required a 38-degree angle but check yours because it may be different. 

I also had to saw the angled slots with the board on its edge. That’s because my tablesaw (like most) tilts to only 45 degrees. This is not far enough for the slot to be cut with the board laying flat. Cutting it on its edge solves this problem. Take a look at your saw and you will see what I mean. Double-check the angle of your jointer knives and saw the slots to match. I added a blade guard to keep things safe.

For the sanding block I used chunks of 3/4-in. MDF with sheets of silicon carbide sandpaper attached with spray-on adhesive. I started with 220 grit and worked my way up to 600 grit for a final honing. 


Click here to read the rest of the article from American Woodworker