American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sharpening Jig Vernal UT

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. Here you will learn how to make your own shop made jigs for woodworking. You also get the option of choosing to buy one of the many different sharpening jig power tools at the hardware supply stores in Vernal, UT listed below.

True Value Hardware
(435) 781-1556
280 W Main St
Vernal, UT
 
Turner Lumber
(435) 789-3581
565 E Main St
Vernal, UT
 
Milt's Ace Home Center
(435) 789-5071
690 W Main St
Vernal, UT
 
The Home Depot
(801)523-0069
135 E 11400 South
Sandy, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(801)292-0238
50 N Market Place Dr
Centerville, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Vernal - Auth Hometown
(435) 781-0409
1783 W Hwy 40
Vernal, UT
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:11-16
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:11-16

Lowe's
(435) 781-9400
2105 West Highway 40
Vernal, UT
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(435)649-1467
1595 East Frontage Rd
Park City, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(435)896-8548
1440 S Technology Drive
Richfield, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(801)254-5762
3852 West 13400 South
Riverton, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Sharpening Jig

Simple Sharpening Jig

I’ve tried several different shop-made jigs for sharpening my jointer and planer knives but this one has proved the simplest to use and make. 

When making this sharpening jig it’s important to make the slots at the correct angle so the bevels of the blades lay perfectly horizontal. This way the sandpaper will have even contact. My jointer blades required a 38-degree angle but check yours because it may be different. 

I also had to saw the angled slots with the board on its edge. That’s because my tablesaw (like most) tilts to only 45 degrees. This is not far enough for the slot to be cut with the board laying flat. Cutting it on its edge solves this problem. Take a look at your saw and you will see what I mean. Double-check the angle of your jointer knives and saw the slots to match. I added a blade guard to keep things safe.

For the sanding block I used chunks of 3/4-in. MDF with sheets of silicon carbide sandpaper attached with spray-on adhesive. I started with 220 grit and worked my way up to 600 grit for a final honing. 


Click here to read the rest of the article from American Woodworker