American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Simple Steam Box Gloversville NY

Attach 2x4 legs to elevate the box above the kettle. One end should be higher to ensure that condensation flows to the drain holes. To accommodate the Lee Valley kettle, I propped one end of the box on a block 9 in. high and the other end on a block 8-1/2 in. high. Then I attached the legs.

The Home Depot
(518)843-1275
135 Hanaford Plaza
Amsterdam, NY
Hours
Mon: 7:00am-10:00pm
Tue: 7:00am-9:00pm
Wed-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

Noble Ace Hardware
(518) 762-3658
130 S Comrie Ave, Eagle Chevrolet
Johnstown, NY
 
L. J. Hand Farm Center
(518) 922-8311
1431 State Hwy 161
Fultonville, NY
 
Lowe's
(518) 954-2400
4825 State Highway 30
Amsterdam, NY
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Amsterdam Riverfront True Value Hardware
(518) 684-6100
1000 River Front Center
Amsterdam, NY
 
Gloversville True Value Hardware
(518) 773-3030
86-88 E Fulton St
Gloversville, NY
 
Tanner Lumber Inc.
(518) 883-3012
4 N Second Ave
Broadalbin, NY
 
Fastenal- Fonda
518-853-1088
25 Broadway St PO Box 544 Fonda, NY, 12068
Fonda, NY
 
Lowe's of Amsterdam
518-954-2400
4825 State Highway 30 Amsterdam, NY, 12010
Amsterdam, NY
 
Fort Plain True Value Hardware
(518) 993-3834
12 Willett St
Fort Plain, NY
 

Simple Steam Box

Simple Steam Box

Build a Box and Add a Steam Kettle: You're Ready to Bend Wood.

By Seth Keller

Building a steam box for bending wood only requires exterior-grade plywood, waterproof glue and an electric tea kettle. 

I bought my kettle from Lee Valley (see Source, below). It came with an aluminum pipe to direct steam into the box. Any electric kettle with a cylindrical spout for inserting a pipe or attaching a hose will do. Most kettles, such as this one, don’t have a large capacity. You’ll need to refill the kettle three or four times per hour for a box this size.

Tongue and groove joints help seal the box’s sides (photo, below right). Form the tongue by milling  a 3/16-in. deep by 3/8-in. wide rabbet along the box’s sides. Use #8 screws, 1-1/2-in. long, and a waterproof glue, such as Titebond III, to assemble the box.

After the glue sets, drill or cut a hole for the kettle’s pipe. The pipe enters at an angle, so make the hole oblong (photo, below left). Attach guide blocks to help direct the pipe into the hole after you refill the kettle. Drill two 1/4 in. holes at one end of the box to allow condensation to drain. Drill more 1/4-in. holes for dowels to support your bending stock. Drill a tight-fitting hole for a meat thermometer near one door. The thermometer isn’t essential, but it allows you to check the box’s temperature. It should remain above 200 degrees throughout the steaming cycle.     

Attach 2x4 legs to elevate the box above the kettle. One end should be higher to ensure that condensation flows to the drain holes. To accommodate the Lee Valley kettle, I propped one end of the box on a block 9 in. high and the other end on a block 8-1/2 in. high. Then I attached the legs. 

Add two-piece doors to the ends. One piece is a cap; the other is a plug. Steam will cause the plug to swell, so make it 1/8 –in. smaller than the opening.  I used large brass hinges to hang the doors. Add screen door hooks to keep the doors shut as you steam away.

Steam passes from the kettle to the box through a pipe inserted into the kettle’s spout.  The kettle must be refilled now and then during the steaming process; two guide blocks help position the pipe when you re-insert it in the hole.

Constructing the box is very easy. Screwed and glued tongue and groove joints keep the box’s seams tight. Support dowels allow steam to circulate around the wood. A plug on the door helps seal the box’s ends.  

Source 

Lee Valley, (800) 871-8158, www.leevalley.com Kettle and pipe, #05F14.02, $37.50.

This story originally appeared in  American Woodworker July 2007, issue #129.   

Source information may have changed since the original publication date.

July 2007, issue #129

Purchase this back issue.

Click here to read the rest of the article from American Woodworker