American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sliding Dovetail Drawers Rockford MI

Accurate dovetailing requires flat, straight stock. You may be able to buy planed wood that’s flat and straight already, but often it’s cupped or bowed. To be sure your wood is flat, we recommend preparing your own stock with a jointer and planer.

The Home Depot
(616)447-0100
2727 Alpine Ave NW
Walker, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Grand Rapids, MI
(616) 957-9663
4265 28th Street SE Ste C
Grand Rapids, MI

Data Provided by:
The Home Depot
(616)724-2280
257 54th Street SW
Wyoming, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockford Hardware
(616) 866-9155
643 Northland Dr NE
Rockford, MI
 
Straight Drive Fasteners LLC
616-785-7977
5224 West River Drive Comstock Park, MI, 49321
Comstock Park, MI
 
The Home Depot
(616)975-4440
4646 28th Street, SE
Grand Rapids, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Johnson's Workbench - GR
(616) 245-9545
1038 Burton SW
Grand Rapids, MI

Data Provided by:
The Home Depot
(616)257-9559
4900 Wilson Ave SW
Grandville, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Rockford
616-863-8604
8177 Graphic Industrial Park Rockford, MI, 49341
Rockford, MI
 
White Creek Lumber & Hardware
(616) 696-0010
13861 White Creek
Cedar Springs, MI
 
Data Provided by:

Sliding Dovetail Drawers

Sliding Dovetail Drawers

Quickly Build a Stack of Drawers Using Your Router Table

By Tom Caspar

Tools You’ll Need

Accurate dovetailing requires flat, straight stock. You may be able to buy planed wood that’s flat and straight already, but often it’s cupped or bowed. To be sure your wood is flat, we recommend preparing your own stock with a jointer and planer. 

You’ll need a router table to make this joint. Our technique is easier to master if your router table has a miter gauge slot, but it isn’t required. You’ll need two router bits: a 1/2-in.-dia. 14-degree dovetail bit, such as the type used with a half-blind dovetail jig, and a 1/4-in. straight bit. Both bits will perform better if they have 1/2-in. shanks.

Mill the Parts

1. Joint and plane lumber for the front, back and sides (Fig. A). The front can be any thickness over 1/2 in. In this example, it’s 3/4 in. thick. Plane the sides to 1/2 in. thick. Make some extra sides for testing the joint’s fit. 

2. Cut the front to width and length. Cut the sides the same width as the front. Trim the sides to length, allowing an extra 1/4 in. for the front dovetails. Leave the back and plywood bottom oversize for now.

Set Up the Router Table

3. Install a dovetail bit in your router table. Raise it 1/4 in. above the table’s top. This height determines the depth of the sockets. It’s arbitrary, but routing a deeper socket can cause a bit to vibrate excessively. 

4. Position the fence 1/2 in. or so away from the bit. This distance determines the setback of the drawer sides, so the precise amount depends on the type of drawer you’re making. If you use 1/2-in.-thick slides and want a standard 1/16-in. gap on either side of the drawer front, make the setback 7/16 in. Use a combination square to adjust the fence so it’s parallel to the router table’s miter gauge slot.

5. Clamp a stop block to the fence (Photo 1). Position the block so your drawer front fits exactly between the bit and the block. Without using math or a ruler, this setup guarantees that the sockets in a drawer front of any size will be exactly the right length, stopping 1/4 in. from the top of the drawer. 

Photo 1. All the joints for this drawer are cut on the router table. Begin by installing a 1/2-in. dovetail bit to make sockets in the drawer front. Clamp a stop block one drawer-front width from the bit. 

Cut the Sockets

6. Rout sockets on the right side of the drawer front (Photo 2). It’s easy to get disoriented here, so mark your fronts well. In this step, the socket will be on your right as you face the drawer. When you lower the board onto the bit, you’ll make a 1/2-in.-dia. hole. Don’t worry; it will be covered by the 1/2-in.-thick drawer side.

Photo 2: Rout the right end of the drawer front. Guide the board with a miter gauge to keep the board square and tight to the fence. Lo...

Click here to read the rest of the article from American Woodworker