American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Small Parts Carousel Bennington VT

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery.

The Home Depot
(802)447-9997
121 N Bennington Rd
Bennington, VT
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

H. Greenberg & Son Inc.
(802) 442-3131
321 Main Street
Bennington, VT
 
W W Building Supply
(802) 464-3022
Route 100
Wilmington, VT
 
H. Greenberg & Son Inc
(413) 664-4576
1366 Curran Highway
North Adams, MA
 
Miles True Value Lbr.
(802) 375-2525
178 Chittenden Dr
Arlington, VT
 
H. Greenberg and Son
802-442-3131
321 Main St. Bennington, VT, 05201
Bennington, VT
 
Hoosick True Value Hardware
(518) 686-7238
21953 Ny 22
Hoosick Falls, NY
 
Carr Hardware True Value
(413) 663-6600
192 State Street
North Adams, MA
 
Deerfield Valley Supply
(802) 464-3364
211 Route 9 W
Wilmington, VT
 
Stanleys Lumber & Building Supplies
(413) 743-0831
20 N Summer St
Adams, MA
 

Small Parts Carousel

Small Parts Carousel

Small Parts Carousel 

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery. All the parts are cut to size and assembled with glue and screws.

My design requires 1-1/2 sheets of plywood, a quarter sheet of 1/8-in. hardboard, six swiveling casters, a 1-1/4-in.-dia. hardwood dowel and a 3-ft.-long 2x4. I used Tapcon cement anchors to bolt this baby to the floor. I got everything I needed at my local home center for about $140. 

Build It

1. Cut and smooth the round carousel bottom (A) and base (B). 

2. Drill 1-1/4-in.-dia. holes through the centers of both pieces.

3. Cut out the shelves (C). Use the round carousel bottom as a template for the curved edges.

4. Mark the locations of the shelves on the two narrow uprights (D) and fasten them. Space the shelves to suit your needs, but be sure to stagger them, so they’re easy to fasten (photo at right).

5. Attach the two shelf/upright assemblies to the wide upright (E). Note: These assemblies must not be mirror images!

6. Fasten the carousel bottom to the completed shelf assembly.

7. Fasten the casters to the base(photo at right).

8. Attach the six feet (F). If your bin is going on an unfinished cement floor, use pressure-treated 2x4 stock for the feet.

9. Attach the center foot (H) to the base and glue in the dowel (G).

10. Position the base and level it with shims.

11. Anchor the base to the floor. 

12. Drill a 1-1/4-in. hole in the glued-up mounting block (J) and fasten it to the carousel bottom. 

13. Mount the carousel on the base.

14. Glue and screw the shelf edges (K). Cut them to length after installation.

Assembly is easy, because everything is screwed and glued. Stagger the shelves and fasten them to the two narrow uprights. Then fasten these assemblies to the wide upright.

The carousel rides on casters and rotates on a large wooden pin.

Click here to read the rest of the article from American Woodworker