American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Small Parts Carousel Brookings SD

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery.

Homestead Building Supplies
(605) 692-6191
823 S Main Avenue
Brookings, SD
 
Brookings Rent-All
(605) 697-5544
803 Main Avenue South
Brookings, SD
 
Ace Hardware
(605) 697-5223
710 22nd Ave S, Brookings Mall
Brookings, SD
 
J & K Building Center
(605) 997-3714
110 S Wind
Flandreau, SD
 
Fastenal- Sioux Falls
605-334-0601
824 E 50th St N Sioux Falls, SD, 57104
Sioux Falls, SD
 
Fastenal- Brookings
605-697-6631
1321 Main Avenue South Brookings, SD, 57006
Brookings, SD
 
Lowe's
(605) 696-2730
812 25Th Avenue
Brookings, SD
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Lowe's of Brookings
605-696-2730
812 25th Ave Brookings, SD, 57006
Brookings, SD
 
The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

NYBERG'S ACE
(605) 338-4223
607 S Sycamore Ave
Sioux Falls, SD
 

Small Parts Carousel

Small Parts Carousel

Small Parts Carousel 

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery. All the parts are cut to size and assembled with glue and screws.

My design requires 1-1/2 sheets of plywood, a quarter sheet of 1/8-in. hardboard, six swiveling casters, a 1-1/4-in.-dia. hardwood dowel and a 3-ft.-long 2x4. I used Tapcon cement anchors to bolt this baby to the floor. I got everything I needed at my local home center for about $140. 

Build It

1. Cut and smooth the round carousel bottom (A) and base (B). 

2. Drill 1-1/4-in.-dia. holes through the centers of both pieces.

3. Cut out the shelves (C). Use the round carousel bottom as a template for the curved edges.

4. Mark the locations of the shelves on the two narrow uprights (D) and fasten them. Space the shelves to suit your needs, but be sure to stagger them, so they’re easy to fasten (photo at right).

5. Attach the two shelf/upright assemblies to the wide upright (E). Note: These assemblies must not be mirror images!

6. Fasten the carousel bottom to the completed shelf assembly.

7. Fasten the casters to the base(photo at right).

8. Attach the six feet (F). If your bin is going on an unfinished cement floor, use pressure-treated 2x4 stock for the feet.

9. Attach the center foot (H) to the base and glue in the dowel (G).

10. Position the base and level it with shims.

11. Anchor the base to the floor. 

12. Drill a 1-1/4-in. hole in the glued-up mounting block (J) and fasten it to the carousel bottom. 

13. Mount the carousel on the base.

14. Glue and screw the shelf edges (K). Cut them to length after installation.

Assembly is easy, because everything is screwed and glued. Stagger the shelves and fasten them to the two narrow uprights. Then fasten these assemblies to the wide upright.

The carousel rides on casters and rotates on a large wooden pin.

Click here to read the rest of the article from American Woodworker