American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Small Parts Carousel East Amherst NY

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery.

Rockler Woodworking and Hardware #11
(716) 631-8922
5085 Transit Rd
Buffalo, NY

Data Provided by:
The Home Depot
(716)639-9600
2065 Niagara Falls Blvd
Amherst, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(716)439-4898
5730 S Transit Rd
Lockport, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(716)871-8800
2100 Elmwood Avenue
Buffalo, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(716)677-7445
1881 Ridge Road
West Seneca, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(716)633-9200
4139 Transit Road
Williamsville, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(716)895-6680
300 Thruway Plaza Dr
Cheektowaga, NY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

RC Tonewoods
(716) 873-6043
1109 Military Road
Buffalo, NY

Data Provided by:
Woodcraft - Buffalo, NY
(716) 674-0795
1900 Ridge Road
West Seneca, NY

Data Provided by:
Advantage Trim & Lumber Co
(716) 827-3915
601 Ohio St
Buffalo, NY

Data Provided by:
Data Provided by:

Small Parts Carousel

Small Parts Carousel

Small Parts Carousel 

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery. All the parts are cut to size and assembled with glue and screws.

My design requires 1-1/2 sheets of plywood, a quarter sheet of 1/8-in. hardboard, six swiveling casters, a 1-1/4-in.-dia. hardwood dowel and a 3-ft.-long 2x4. I used Tapcon cement anchors to bolt this baby to the floor. I got everything I needed at my local home center for about $140. 

Build It

1. Cut and smooth the round carousel bottom (A) and base (B). 

2. Drill 1-1/4-in.-dia. holes through the centers of both pieces.

3. Cut out the shelves (C). Use the round carousel bottom as a template for the curved edges.

4. Mark the locations of the shelves on the two narrow uprights (D) and fasten them. Space the shelves to suit your needs, but be sure to stagger them, so they’re easy to fasten (photo at right).

5. Attach the two shelf/upright assemblies to the wide upright (E). Note: These assemblies must not be mirror images!

6. Fasten the carousel bottom to the completed shelf assembly.

7. Fasten the casters to the base(photo at right).

8. Attach the six feet (F). If your bin is going on an unfinished cement floor, use pressure-treated 2x4 stock for the feet.

9. Attach the center foot (H) to the base and glue in the dowel (G).

10. Position the base and level it with shims.

11. Anchor the base to the floor. 

12. Drill a 1-1/4-in. hole in the glued-up mounting block (J) and fasten it to the carousel bottom. 

13. Mount the carousel on the base.

14. Glue and screw the shelf edges (K). Cut them to length after installation.

Assembly is easy, because everything is screwed and glued. Stagger the shelves and fasten them to the two narrow uprights. Then fasten these assemblies to the wide upright.

The carousel rides on casters and rotates on a large wooden pin.

Click here to read the rest of the article from American Woodworker