American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Small Parts Carousel Walterboro SC

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery.

Walterboro Do it Best Hardware
(843) 549-5713
645 S Jefferies Blvd
Walterboro, SC
 
Woodcraft - Greenville, SC
(864) 627-8760
1327 Miller Road
Greenville, SC

Data Provided by:
The Home Depot
(803)359-1194
5600 Sun Set Blvd
Lexington, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 1:30pm-8:00pm

The Home Depot
(803)419-9336
285 Forum Drive
Columbia, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Paulownia Barn, LLC
(803) 381-8735
405 Hydrick Road
Swansea, SC

Data Provided by:
Westbury Ace Hardware
(843) 539-3333
1050 Bells Hwy
Walterboro, SC
 
The Home Depot
(843)851-0468
190 Marymeade Dr
Summerville, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(864)963-7732
669 Fairview Road
Simpsonville, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(843)357-3777
12262 Hwy 17 Bypass
Murrells Inlet, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(864)574-2922
121 Dorman Center Drive
Spartanburg, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Small Parts Carousel

Small Parts Carousel

Small Parts Carousel 

While visiting an antique shop, I discovered a way to store all that indispensible small stuff that used to clutter my workshop. On display was a rotating bolt cabinet from an old-fashioned hardware store. When I got home, I design-ed this carousel that rotates on inverted swivel casters. It’s easy to build, because there’s no complicated joinery. All the parts are cut to size and assembled with glue and screws.

My design requires 1-1/2 sheets of plywood, a quarter sheet of 1/8-in. hardboard, six swiveling casters, a 1-1/4-in.-dia. hardwood dowel and a 3-ft.-long 2x4. I used Tapcon cement anchors to bolt this baby to the floor. I got everything I needed at my local home center for about $140. 

Build It

1. Cut and smooth the round carousel bottom (A) and base (B). 

2. Drill 1-1/4-in.-dia. holes through the centers of both pieces.

3. Cut out the shelves (C). Use the round carousel bottom as a template for the curved edges.

4. Mark the locations of the shelves on the two narrow uprights (D) and fasten them. Space the shelves to suit your needs, but be sure to stagger them, so they’re easy to fasten (photo at right).

5. Attach the two shelf/upright assemblies to the wide upright (E). Note: These assemblies must not be mirror images!

6. Fasten the carousel bottom to the completed shelf assembly.

7. Fasten the casters to the base(photo at right).

8. Attach the six feet (F). If your bin is going on an unfinished cement floor, use pressure-treated 2x4 stock for the feet.

9. Attach the center foot (H) to the base and glue in the dowel (G).

10. Position the base and level it with shims.

11. Anchor the base to the floor. 

12. Drill a 1-1/4-in. hole in the glued-up mounting block (J) and fasten it to the carousel bottom. 

13. Mount the carousel on the base.

14. Glue and screw the shelf edges (K). Cut them to length after installation.

Assembly is easy, because everything is screwed and glued. Stagger the shelves and fasten them to the two narrow uprights. Then fasten these assemblies to the wide upright.

The carousel rides on casters and rotates on a large wooden pin.

Click here to read the rest of the article from American Woodworker