American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Speaker Stand with Hidden Storage Brookings SD

Don't you love hearing great sound with your movies at home? A pair of these oak stands puts today's small speakers at the ideal height—3 ft. above the floor. We've built cabinets under the speakers that hold a total of 60 DVDs behind secret doors. And we've tucked the speaker wires out of sight—they run inside the stands.

Rykhus-Nelson Siding Windows & Gutters
(605) 692-6800
505 1st St S
Brookings, SD
 
Mac's Inc
(605) 225-4029
222 6th Ave SW
Aberdeen, SD
 
Seamless Gutters
(605) 345-4129
14038 Sd Highway 25
Webster, SD
 
Krug Products
(605) 256-2851
419 SW 2nd St
Madison, SD
 
Andor Inc
(605) 886-2457
9 1/2 N Maple
Watertown, SD
 
Mesabi Tools Inc
(605) 482-8264
22684 453rd Ave
Madison, SD
 
Johnson Appliance
(605) 338-9911
1612 W 41st St
Sioux Falls, SD
 
Gutter Specialists
(605) 339-0726
Sioux Falls, SD
 
H & R Roofing of South Dakota Inc
(605) 368-2148
27491 471st Ave
Harrisburg, SD
 
Northman Snowplows
(605) 543-5607
47219 W Schweigers Cir
Sioux Falls, SD
 

Speaker Stand with Hidden Storage

Speaker Stand with Hidden Storage



Don't you love hearing great sound with your movies at home? A pair of these oak stands puts today's small speakers at the ideal height—3 ft. above the floor. We've built cabinets under the speakers that hold a total of 60 DVDs behind secret doors. And we've tucked the the speaker wires out of sight—they run inside the stands. 



Start with Straight-Grained Wood
Wood selection makes all the difference in this project. Straight-grained pieces emphasize the stand's simple lines. Wild or angled grain is distracting, but often it's the norm in oak. No problem. If you don't mind wasting some wood, you can make your own great-looking straight-grained boards. Begin by selecting boards for the stiles and rails. You don't need many. It doesn't matter what angle the grain runs at in these pieces, as long as some of it is straight. Save the parts of these boards with really wild grain for the frames (K) and top (P) since their faces don't show. Rip the boards at an angle that follows the grain (Photo 1). Use the new edge to cut your stiles and rails.

PHOTO 1:
Straight-grained wood complements the simple lines of this project. This simple jig with toggle clamps lets you rip straight-grained pieces from ordinary boards.

PHOTO 2:
Cut grooves in the rails and stiles to hold plywood panels and splines. The rails are very short and unsafe to hold by themselves, so push them with a shop-made jig (Fig. B).

Rail, Stiles and Panels
The storage cabinet is basically four frame-and-panel assemblies with similar stiles and rails. They are grooved to hold plywood panels  (G) and splines (E, F). The splines join each assembly. We'll use a standard blade to cut the grooves, rather than a dado blade, because 1/4-in. plywood is usually undersized.
1. Rip and crosscut the stiles (A, B) and rails (C, D). Hang on to your offcuts to use as trial pieces when making the grooves. Note that the stiles are two different widths. The back has two narrow stiles; the door has two wide ones. The sides have a narrow stile in front, a wide stile in back.
2. Cut the plywood panels (G) and use leftover scraps to make splines.
3. To make assembly easier, use sandpaper to slightly round the edges of the panels.
4. Select and mark the best-looking side of each rail and stile as its face. Place the face against the fence each time you cut a groove. That way, any slight variations in wood thickness will create uneven joints on the inside rather than the outside of the speaker stand.
5. Set your blade to 1/4-in. cutting depth and set your fence 1/4 in. from the blade. Cut one kerf in some trial pieces and every stile and rail (Photo 2; Fig. A, Detail 1 ). Move the fence and make a second pass in one of the trial pieces. Use a spline to check the fit of the groove. The spline should slip in easily, allowing room for glue. Adjust the fence if necess...

Click here to read the rest of the article from American Woodworker