American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Spiral Router Bits Littleton CO

I've routed miles of grooves in my life, but the quality of cut I've been getting from spiral bits still amazes me. I love these bits! The secret is in the spiral design, which cuts the wood through a shearing action.

The Home Depot
(720)344-7645
1200 Mayberry Road
Littleton, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)706-1500
8477 S Yosemite Ave
Lone Tree, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)765-0400
500 S Santa Fe Dr
Denver, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcraft - Denver, CO
(303) 290-0007
6770 S. Peoria St
Centennial, CO

Data Provided by:
The Home Depot
(303)232-6303
6701 W Alameda Ave
Lakewood, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)794-0352
3000 W Belleview Ave
Littleton, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)922-0444
3130 S Sheridan Blvd
Denver, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Rockler Woodworking and Hardware #3
(303) 782-0588
2553 S. Colorado Blvd. Suite 108
Denver, CO

Data Provided by:
The Home Depot
(303)799-9071
9401 E Arapahoe Rd
Greenwood Village, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(720)524-2480
860 S Colorado Blvd
Glendale, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Data Provided by:

Spiral Router Bits

Provided By:

Spiral Router Bits

I've routed miles of grooves in my life, but the quality of cut I've been getting from spiral bits still amazes me. I love these bits! The secret is in the spiral design, which cuts the wood through a shearing action. This offers three big benefits. First, spiral bits leave a silky smooth surface, even on end grain. Second, they can eliminate chipping on the face of chip-prone materials, such as veneered plywood and melamine. Third, it takes less effort to rout with a spiral bit. This reduces the load on your router and means faster, easier routing for you. The spiral can be either an up-cut spiral, a down-cut spiral or a combination up- and down-cut spiral. The bits can even be found with bearings for trim and pattern cutting. Spiral bits are available with one, two or three flutes. Single-fluted bits cut the fastest; bits with three flutes produce the smoothest surface. Two-fluted spiral bits are the most commonly available and provide an excellent balance of speed and quality of cut. You can buy spiral bits with cutting diameters ranging from 1/8 in. to 1-1/8 in. They cost between $10 and $100 each, depending on size and whether they are carbide or high-speed steel. A 1/2-in-diameter solid carbide spiral bit, for example, costs about $45; the same size bit in high-speed steel will run about $15. Carbide will stay sharp longer than high-speed steel, but is brittle and easily broken or chipped if the bit is dropped or is pushed too hard when routing. This is especially true of bits that have a 1/4-in. cutting diameter or less. A high-speed steel spiral bit will save you money, but use it only on solid wood. Manufactured materials, such as plastic laminate and melamine, will quickly dull a high-speed steel bit. Solid carbide and high-speed steel spiral bits can be sharpened for about $10 to $15 each. Your local saw blade sharpening service should be able to do it for you or to send it to someone who can. All major router bit companies sell spiral router bits.



Up-Cut Spiral Bit
The up-cut spiral router bit is an excellent bit for cutting deep mortises and grooves. The end of the bit has square cutting edges that permit plunge routing and leave a flat bottom to the mortise. The up-cut spiral of the cutting edge pulls the chips up and out, preventing the chips from getting packed into the mortise, which is common with a standard straight router bit. Up-cut spiral bits also work great in a router table because they pull the workpiece down onto the table during cutting.


Down-Cut Spiral Bit
The down-cut spiral router bit excels at routing dados and through slots. The downward shearing action of the bit guarantees a chip-free surface on chip-prone materials, such as melamine (shown below), plastic laminates and delicate wood veneers. The bit's downward cutting action puts downward pressure on thin material and helps hold it down. Down-cut spiral bits should not be used in a router...

Click here to read the rest of the article from American Woodworker