American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Joinery San Angelo TX

Learn more about stile and rail joinery and other different joinery techniques. It’s important you’re connecting wood the right way by using the perfect wood joinery tools. Your woodworking pieces will benefit from your research into more joinery techniques. Find the wood joinery tools you need at the hardware supply stores in San Angelo, TX listed below.

The Home Depot
(325)223-0439
4363 Houston Harte Exwy
San Angelo, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Angelo Bolt & Industrial Supply
325-655-0075
808 Warehouse Road San Angelo, TX, 76903
San Angelo, TX
 
Sunset Mall
(325) 942-5281
4000 Sunset Mall
San Angelo, TX
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Westlake Ace Hardware
(325) 942-6602
1821 Knickerbocker Rd
San Angelo, TX
 
The Home Depot
(956)440-7779
4710 S Expressway 83
Harlingen, TX
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Southern Fastening Systems- San Angelo
915-944-8091
922 Arroyo Drive San Angelo, TX, 76903
San Angelo, TX
 
Fastenal- San Angelo
325-486-1626
701 Knickerbocker Rd San Angelo, TX, 76903
San Angelo, TX
 
LOWE'S OF SAN ANGELO, TEX.
325 942-3100
5301 SHERWOOD WAY SAN ANGELO, TX, 76904
San Angelo, TX
 
Lowe's
(325) 942-3100
5301 Sherwood Way
San Angelo, TX
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(817)447-6602
300 NW John Jones
Burleson, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Joinery

Stile and Rail Joinery


STILE-CUTTING CONFIGURATION

 

RAIL-CUTTING CONFIGURATION


A reversible stile and rail bit makes perfect-fitting frames for doors and cabinets without dowels, mortises or biscuits.

Reversible bits have removable profile- and slot-cutting wings alongwith shims and a guide bearing mounted on a single shaft. Depending onits orientation, the profile cutter either creates the profile  on thestile (above, left) or its coped negative on the rail (above, right).Changing the setup  means disassembling the bit (below), rearrangingthe wings and reassembling—a two-minute process. Make sure to orientthe cutting wings correctly, so they face into the cut. Shims allowadjusting the fit.

One of the best buys you can make for your table-mounted router is aset of stile-and-rail bits. These bits allow you to join frame piecestogether by making a decorative version of the tongue and groove joint.This joint is often called a “cope and stick” joint,  because the railis coped to fit around the profile that's “stuck” onto the stile. Whenassembled, two stiles and two rails form a frame with a groove aroundits inside edge, perfect for holding a panel. Stile-and-rail bits comein a variety of profiles (Fig. A) and are great for making kitchencabinet doors and other frame and panel structures. Most manufacturersoffer them either as matched two-bit sets or as a single “reversible”bit. With the two-bit set you get one bit to make a “profile” cut onlong grain (the stile cutter) and another to make a matching “coped”cut on the end-grain (the rail cutter). With the single, reversible-bitsets you get removable parts that can be configured to make both cuts.

Matched sets with separate bits are best in production shops, butreversible bits are a good choice for anyone working with a budget,because they usually cost less than matched sets and still offer greatperformance. Using a reversible bit is a piece of cake (Photos 1 - 6,below), as long as you remember to make the cope cuts face-side up andprofile cuts face-side down. Making the changeover from profile to copecutting (or back) takes only a few minutes. You'll be impressed withthe quality of the fit and the speed with which you can make a quantityof doors or frames.


Fig. A: Stile-and-rail bits come in a variety of decorative profiles.

PHOTO 1
Startby making cope cuts on the ends of the rails. Install the bitconfigured for rail-cutting. The use a straightedge to set the fenceflush with the guide bearing, to assure a smooth pass

 

PHOTO 2
Make test end-grain cuts. You'll need a sled to hold the rail safelyand ensure a square cut. Simply glue a block of wood with onesquarely-cut end onto a larger piece of 1⁄4-in. plywood, aligned on oneedge. Then attach a toggle clamp. Clamp the rails in the...

Click here to read the rest of the article from American Woodworker