American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Stowaway Bench Conway SC

You’ll need a tablesaw, dado blade, jigsaw, router and beading bit. We used 15 lineal ft. of 1x12 Douglas fir dimensional lumber . Dimensional lumber comes planed on all four surfaces and measures 3/4-in.

The Home Depot
(843)916-2229
951 Oak Forest Lane
Myrtle Beach, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF CONWAY, SC
843 234-6033
2301 HIGHWAY 501 EAST CONWAY, SC, 29526
Conway, SC
 
Kmart 7555 / Cross Merch
(843) 248-2411
1610 Church St
Conway, SC
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Lowe's
(843) 650-1400
8672 Highway 17 Bypass
Myrtle Beach, SC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Lowe's
(843) 626-1700
1160 Seaboard Street
Myrtle Beach, SC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(843)357-3777
12262 Hwy 17 Bypass
Murrells Inlet, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Terry's Do it Best Hardware
(843) 365-9300
5275 Hwy 501 West
Conway, SC
 
Lowe's
(843) 234-6033
2301 Highway 501 East
Conway, SC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

MID-ATLANTIC FASTENERS/Myrtle Beach
(843) 293-8795
3195B Highway 17 Bypass Myrtle Beach, SC, 29577
Myrtle Beach, SC
 
Kmart 3817 / Cross Merch
(843) 626-3066
1403 N Kings Hwy
Myrtle Beach, SC
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Stowaway Bench

Stowaway Bench

This bench will fit in any entryway, and store your umbrella and gloves too!

by Jon Stumbras

This country-style bench will cut the clutter by the door and serve as a resting spot to put on your shoes. The lid opens up to reveal a handy storage area. At only 11-in. wide by 44-in. long, it neatly fits in an entryway or mudroom. And it’s simple enough to be a good weekend project.

Tools and Materials

You’ll need a tablesaw, dado blade, jigsaw, router and beading bit. We used 15 lineal ft. of 1x12 Douglas fir dimensional lumber (see Sources, below). Dimensional lumber comes planed on all four surfaces and measures 3/4-in. thick by 11-1/4-in. wide. This is wide enough for the widest parts, so there is no edge gluing of boards required for this project. The Douglas fir lumber costs approximately $100.

Cut the Parts

It’s important that the lid (A) be as flat as possible. Since it’s common for wide boards to be slightly warped, it’s best to pick the flattest one for the lid before cutting out any other parts. Then rip and crosscut the lid, legs (B) and rails (C) to final dimensions (see Cutting List, page 78). The legs and lid are too wide to crosscut with a standard tablesaw miter gauge. A simple shop-made crosscut sled solves this problem (Photo 1). For complete details on building a crosscut sled see “The Ultimate Shop-Built Crosscut Sled” . Cut the bottom (D) to final length, but leave it 1-in. oversize in width. It will be custom fit later on.

Shape the Legs and Rails

Start by cutting the dadoes in the two legs (Photo 2 and Figs. A and B). Then cut the notches in the upper corners of the legs. This is a three-step process. First, make two vertical cuts in each leg (Photo 3). Most tablesaws will not be able to cut the full 3-1/2-in. depth that’s required for this cut. This is not a problem and has the benefit of preventing the scrap from falling out during the final cuts. 

Second, set the miter gauge 95 degrees to the left of the blade and crosscut the left-hand notches (when facing the dado) on each leg (Photo 4). 

Third, set the miter gauge 95 degrees to the right and crosscut the right-hand notches (Photo 5). Break off the waste with your hand, and clean up the remaining wood with a chisel (Photo 6). Now test fit the rails into the notches. The tops of the rails and the tops of the legs should be flush. If either is proud, trim it flush. Next, cut the angle on the sides of the legs (Fig. B) with a jigsaw and smooth the cut with a hand plane or sanding block. 

The arcs at the bottom of the legs come next. Start by drawing a 4-in.- radius circle on a piece of cardboard. Cut it out and use it as a template. Position it according to the dimensions in Fig. B and draw the arc. Then cut the arc out of the leg with a jigsaw. Clean up the rough edges with sandpaper.

Next, rout the bead on the bottom edge of the rails (Photo 7)...

Click here to read the rest of the article from American Woodworker