American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Sunburst Patio Table Fargo ND

Tired of outdoor tables made of metal or plastic? This table has the richness and warmth that only wood can provide. Read on to learn how to make the table by yourself.

The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Scheels Ace Hardware
(701) 232-8903
3202-13th Ave S
Fargo, ND
 
Fastenal- Fargo
701-271-1055
3239 15th St S Suite A Fargo, ND, 58106
Fargo, ND
 
Lowe's
(701) 433-2160
5001 13Th Avenue Sw
Fargo, ND
Hours
M-SA 7 am - 9 pm
SU noon-8 pm

ACME TOOLS- Fargo
(701) 476-4600
920 36th Street SW Fargo, ND, 58103
Fargo, ND
 
Lamperts
(701) 492-0292
4115 32nd Ave Sw
Fargo, ND
 
West Acres Regional S/C
(701) 281-5800
3902 13Th Ave South Ste 600
Fargo, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

LOWE'S OF FARGO, ND
701 433-2160
5001 13TH AVENUE SW FARGO, ND, 58103
Fargo, ND
 
Simonson Lumber & Hdw True Value
(701) 232-3281
2400 Main Ave
Fargo, ND
 
Kmart 4057 / Cross Merch
(701) 232-8943
2301 S University Dr
Fargo, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Sunburst Patio Table

Sunburst Patio Table

By David Radtke

Download the pdf file.

Tired of outdoor tables made of metal or plastic? This table has the richness and warmth that only wood can provide.

It’s built to stand up to the weather, so it’s perfect for a patio, porch or sunroom. The 44-in. top features a stunning sunburst radial design and seats four comfortably.  The sturdy base construction makes for a rock-solid table. There’s a center hole for an umbrella canopy and plenty of room beneath for the counterweight. 

I built my table out of rot-resistant white oak with splines and grooves in the tabletop and dowel joints in the legs. I chose epoxy for strong, weatherproof joints.

I simplified the tabletop’s complex construction by using an MDF pattern board that doubles as a machining and clamping jig. The pattern board is used along with a simple trammel to accurately machine the fussy curved joints on the pie shaped slats and to cut the outer ring and the center hub. I’ll  show you how to make cam clamps that lock the top’s parts in position for routing and gluing. 

The base may appear challenging to build, but I’ll also show you a system, using a pair of ordinary handscrews, to make the job go smoothly. 

Make The Pattern Board

The best way to deal with the geometry and joinery of the tabletop is to draw it out on a 4x4-ft. piece of 3/4-in. sheet stock (Fig. B) I call it a pattern board. 

Build The Outer Ring

1. Measure the length (long point to long point) of a section of the outermost ring on the pattern board. Our measurement came to 11-13/16 in. but check yours since it may vary. 

2. Cut the outer ring segments (A) to length on a sled (Photo 1; Fig. C).

Photo 1: The table is built from the outside in. Start by mitering the outer ring segments with a sled. Cut one end of each segment without the stop in place. Add the stop and miter the opposite end. A shop made cam lock holds the piece in place.

3. Dry fit the segments on the pattern board to make sure all the miters are tight. You may have to adjust the angle of the last miter. If you do, mark the joint so it can be reassembled correctly.

4. Add backer blocks to support the inside edge of the outer ring (Photo 2).  

Photo 2: Dry-fit the ring segments on a pattern board that has a full-size drawing of the top. Pin backer blocks behind each segment.

5. Cut the cam locks on the drill press using a 2-1/2- in.-dia. hole saw and a table that slopes 10 degrees (Photo 3). 

Photo 3: Make eccentric cam locks on the drill press using a 2-1/2-in. hole-saw and a support. The angled edges of the disc act like a cam lock when screwed to a board.

6. Screw the cam locks onto the pattern board so the short radius is just shy of the spacer. The sacrificial spacers keep the cam locks from being cut as the ring is routed out in the following steps. 

7. Cut the slots in the mitered ...

Click here to read the rest of the article from American Woodworker