American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Super-Smooth Poly Finish Dubuque IA

Synthetic steel wool creates an even, silky smooth finish that’s a joy to look at and feel. This age-old two-step technique is commonly used on shellac and lacquer finishes, but it can work well on water- and oil-based polyurethane, too. The only drawback with poly is that it is difficult to bring up to a high gloss.

ABC Supply Co.,Inc/Dubuque
563-557-9920
250 S. Main Street Dubuque, IA, 52003
Dubuque, IA
 
Key West True Value Hardware
(563) 582-2100
2100 Stone Hill Dr
Dubuque, IA
 
Lowe's
(563) 588-8008
4100 Dodge Street
Dubuque, IA
Hours
M-SA 6:30 am - 9 pm
SU 8 am - 7 pm

Steve's Ace Home Garden
(563) 690-1500
3350 John F Kennedy Rd, NW Arterial & 32nd st
Dubuque, IA
 
Steve's Ace Hardware
(563) 588-9755
200 S Locust St
Dubuque, IA
 
Kennedy Mall
(563) 589-1500
555 John F Kennedy Rd
Dubuque, IA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

LOWE'S OF DUBUQUE, IA.
563 588-8008
4100 DODGE ST. DUBUQUE, IA, 52003
Dubuque, IA
 
Kmart 4018 / Cross Merch
(563) 588-2361
2600 Dodge St
Dubuque, IA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Gierke-Robinson Co- Dubuque
319 556 1185
Highway 20 West Dubuque, IA, 52003
Dubuque, IA
 
Fastenal-Dubuque
563-556-7725
3185 Hughes Court Suite E Dubuque, IA, 52003
Dubuque, IA
 

Super-Smooth Poly Finish

Super-Smooth Poly Finish

A Defect-Free, Even Finish with a Brush

by Eric Smith

Polyurethane is a tough, high-quality finish, ideal for tabletops and other surfaces that take a lot of abuse. But no matter how clean your finishing area or how good your brushing technique, a few bubbles, dust particles and streaky spots always manage to sneak into the final coat (Photo 1). Directions on the can don’t say anything about it—leaving you to assume a less-than-perfect finish must be your own fault. However, the solution is quite simple—rub out the finish with fine sandpaper and synthetic steel wool. Sanding removes defects and levels ridges.

Photo 1: The Problem: A few dust nibs, broken brush bristles and bubbles are almost inevitable on big horizontal surfaces finished with slow-drying polyurethane. 

Synthetic steel wool creates an even, silky smooth finish that’s a joy to look at and feel. This age-old two-step technique is commonly used on shellac and lacquer finishes, but it can work well on water- and oil-based polyurethane, too. The only drawback with poly is that it is difficult to bring up to a high gloss. If a satin or semi-gloss look is what you’re after, this technique will give you great results.

Materials and Supplies

Sandpaper

Sandpaper is used to flatten the finish and remove dust nibs and brush marks. Stearated aluminum-oxide sandpaper is by far the best product for sanding a finish. Stearated paper has dry lubricants that help prevent “corning” or the balling up of finish on the paper. Wet-dry silicon-carbide paper balls up like crazy if you don’t use water as a lubricant. The trouble with wet sanding is the water slurry can make it difficult to see your progress.  

Synthetic Steel Wool

I used synthetic steel wool on both water- and oil-based polyurethane. Traditional steel wool is not recommended for water-based finishes; it sheds steel particles that leave a mess and give the user steel wool slivers. Synthetic steel wool pads equivalent to 00 steel wool are widely available at home centers and hardware stores. Fine synthetic wool equivalent to 0000 steel wool is harder to find. I had good luck at auto-body supply stores and mail-order woodworking suppliers (see Sources, below). 

Powdered Abrasives

Pumice and rottenstone are sold at some paint stores and at woodworking suppliers. Pumice is ground volcanic glass that comes in grades from  1F (coarse) to 4F (fine). Rottenstone is even finer than 4F pumice. It’s made of ground limestone (see Sources, below).

Build a Good Foundation for the Finish

1. I use 220-grit sandpaper for final sanding on raw wood. I always sand a little bit longer than I think is necessary. Then I vacuum thoroughly and wipe the wood with a clean, soft cloth until I stop getting dust on my fingers when I run them over the wood. 
2. Use grain filler on open-pored woods, such as oak or walnut....

Click here to read the rest of the article from American Woodworker